Uline H-4602 Bruksanvisning
Sidor 18 våg
Läs bruksanvisningen för Uline H-4602 gratis online eller ladda ner PDF:en. 22 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
PAGE 1 OF 180825 IH-4602
STAINLESS STEEL
LOW PROFILE FLOOR SCALE
1-800-295-5510
uline.com
H-4602, H-4603, H-4604
H-10905, H-10906, H-10907
INTRODUCTION
INTRODUCTION
SITE SELECTION
Select a site for the floor scale where it is least likely to
be damaged by forklifts and other material handling
devices. Floor scale load cell weighing elements are
prone to overload damage caused by side impacts,
falling objects and weight loads that exceed the rated
capacity of the scale.
Site should be:
• Level within 1/4".
• Free from vibration.
• Clean of debris.
• Out of the way of vehicle traffic patterns, unless
installed in a pit while having a rated capacity
that exceeds all loaded vehicle weights that could
possibly drive onto or contact the scale.
The cable from the floor scale to the digital weight
indicator should be run through a conduit to protect it
against possible damage. Running the instrument cable
through a conduit is the best method of protection.
UNPACKING
1. Inspect your shipment for damage. If you see visible
signs of damage, notify carrier at once.
2. Remove floor scale from the shipping pallet. Digital
indicator and power cord should be attached.
3. Remove feet from package.
FEET INSTALLATION AND LEVEL ADJUSTMENTS
NOTE: Scale is shipped without feet installed to
protect against damage in transit.
1. Using a pry bar, lift scale up and thread feet into the
cells counterclockwise.
2. Screw feet until top of the threaded stem is flush with
top of the cell.
NOTE: Do not screw feet more than ten turns.
3. Place the scale on the ground to check if scale is
level and that all four feet are solid on the ground.
4. Make adjustments as needed if scale is not level.
5. Once level, tighten locknuts on feet to lock into
place.
RAMP INSTALLATION (OPTIONAL)
1. Set floor scale in desired location.
2. Position ramp on desired side of the scale. There
should be 1/8 – 1/4" gap between the scale and
ramp. (See Figure 1)
3. To hold ramp in place, drill 1/2 x 3" anchors (not
included) through ramp's mounting tabs into the
floor.
NOTE: Scale and ramp should not be touching.
Contact will impede scale from weighing
accurately.
Para Español, vea páginas 7-12.
Pour le français, consulter les pages 13-18.
TOOL NEEDED
Pry Bar
Figure 1
RampScale
Anchor goes here
Mounting Tabs
Produktspecifikationer
| Varumärke: | Uline |
| Kategori: | våg |
| Modell: | H-4602 |
Behöver du hjälp?
Om du behöver hjälp med Uline H-4602 ställ en fråga nedan och andra användare kommer att svara dig
våg Uline Manualer
Uline H-1649 Bruksanvisning Uline H-11909 Bruksanvisning Uline H-1117 Bruksanvisning Uline H-3004 Bruksanvisning Uline H-8031 Bruksanvisning Uline H-754 Bruksanvisning Uline H-10904 Bruksanvisning Uline H-9673 Bruksanvisning
Populära i våg
våg Manualer
Nyaste våg Manualer
Gemini Pro GFS90S Bruksanvisning Maul 1623082 Bruksanvisning Taylor 5331995 Bruksanvisning Vivax PS-158W Bruksanvisning Vivax PS-154WG Bruksanvisning Tesla BS103W Bruksanvisning Concept Perfect Health VO5100 Bruksanvisning Tesla BS102B Bruksanvisning Vivax PS-156WG Bruksanvisning Scarlett SC-BS33ED103 Bruksanvisning