Valcom VIP-801 Bruksanvisning

Valcom Inte kategoriserad VIP-801

Läs gratis den bruksanvisning för Valcom VIP-801 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 31 personer och har ett genomsnittsbetyg på 3.9 stjärnor baserat på 16 recensioner. Har du en fråga om Valcom VIP-801 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

1 947791

INPUTS

AUDIOAUX

OUTIN AUDIO CC

+24V DC

N.C.

N.O.

N.C.

N.O.

COM

Issue 1

VIP-801-IC

InformaCast

Compliant

Network Audio Port

INSTALLATION

Mounting

The VIP-801-IC is designed for wall or table

mounting.

Table: Provided with the VIP-801-IC are four rubber

pads. Peel the pads from their carrier backing and

place at the four corners of the bottom of the unit.

Wall: Using the brackets and screws provided,

secure the VIP-801-IC to the wall.

Power Connections

The preferred method of powering a VIP-801-IC is

via a power over Ethernet switch meeting the

802.3af specification. If the rear panel barrel

connector is used for power, the preferred power

supply is a Valcom VIP-324.

Make all required signal connections before

applying power to the unit. If powering via 802.3af

Power over Ethernet, make sure all signal

connections via the back panel are made then

connect the VIP-801-IC to the Ethernet switch.

If power is supplied via the barrel connector, make

sure all signal connections are secure. Attach the

unit to the network via the front panel RJ-45

Ethernet connector. Apply power by plugging the

power supply into the VIP-801-IC via the barrel

connector on the rear of the VIP-801-IC.

Network Connection

The VIP-801-IC has one CAT-5 RJ-45 network

connector on the front panel.

Use the supplied CAT-5 patch cable to connect the

VIP-801-IC to an Ethernet switch.

Signal Connections

The VIP-801-IC has 2 active signal connectors on

the rear panel:

 2 Pin screw terminal for audio output

 6 Pin screw terminal for relay connections

(Connectors AUX, K2, INPUTS are not used)

Audio Out: Typically connects to Self Amplified

Speakers or into an amplifier. AUX Input audio

mutes when Audio Out is receiving page audio.

Relay Channels: Access to the form C relay is

provided via three screw terminals (on a six pin

screw terminal block) labeled K1. The common

contact is the middle terminal with the normally

closed (N.C) contact on the left and the normally

open (N.O.) contact on the right. Relay contacts

are rated for 1A @ 24VDC.

Rear View

Status Indicator Lights

The VIP-801-IC has 3 status indication lights on the

front panel:

STATUS: Flashes during normal operation and

solid during system startup.

LINK: Indicates a 100 Mbit Ethernet connection

when illuminated. A non-illuminated LINK LED

indicates a 10 Mbit connection or no network

connection.

ACT: Indicator flashes to indicate network activity.

Setup

The VIP-801-IC will automatically acquire an IP

address (using DHCP) and connect to the

InformaCast server when connected to the network

and powered up. Information specific to your

application will need to be programmed into the

InformaCast server. Refer to the InformaCast

documentation for further information.

Produktspecifikationer

Varumärke:	Valcom
Kategori:	Inte kategoriserad
Modell:	VIP-801
Vikt:	562.5 g
Bredd:	156 mm
Djup:	133.3 mm
Höjd:	35 mm
Rackmontering:	Nej
Formfaktor:	Låda
Temperatur vid drift:	0 - 40 ° C
Intervall för relativ operativ luftfuktighet:	0 - 85 %
Stöd för nätverksprotokoll:	DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
Stöd för garanterad tjänstekvalitet (QoS):	Nej
Efterlever industristandard:	802.3af
Anslutningstyp:	RJ-45
Antal talkanaler stöds (max):	1