Velleman K8023 Bruksanvisning
Velleman
Fjärrkontroll
K8023
Läs gratis den bruksanvisning för Velleman K8023 (20 sidor) i kategorin Fjärrkontroll. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 12.5 recensioner. Har du en fråga om Velleman K8023 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/20
10 Channel, 2-Wire REMOTE CONTROL
K8023
H8023IP-1
Control up to 10 devices from a
distance using only 2 wires.
2
Features:
Microprocessor controlled.
Inputs can be push-buttons, switches or open collector outputs from another device.
The receiver section provide 10 open collector outputs which allow you to control relays directly.
Terminal block connectors for all input and output connections are included.
All outputs are provided with LED indication.
Can be used with our kits: K8000,K8006,K8046,K8050,…
Can be connected to our standard relay card: K6714, K6714-16
Specifications:
10 open collector outputs 50V/100mA
Tested to a distance of up to 50m (55 yards) between control- and receiver section.
Operating voltage: Single 12-15V AC or DC, 300mA.
Dimensions control pcb (wxdxh): 70x50x16mm (2,7”x2”x0,6”).
Dimensions receiver pcb (wxdxh): 103x50x24mm(4”x2”x1”).
Features & Specifications
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.
Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes.
Values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
Produktspecifikationer
| Varumärke: | Velleman |
| Kategori: | Fjärrkontroll |
| Modell: | K8023 |
Behöver du hjälp?
Om du behöver hjälp med Velleman K8023 ställ en fråga nedan och andra användare kommer att svara dig
Fjärrkontroll Velleman Manualer
9 December 2024
25 Augusti 2024
24 Augusti 2024
23 Augusti 2024
22 Augusti 2024
19 Augusti 2024
7 Augusti 2024
3 Augusti 2024
30 Juli 2024
26 Juli 2024
Fjärrkontroll Manualer
- Adj
- TCM
- HQ
- Magnum
- Mosconi
- Danfoss
- Technaxx
- EVE
- Omega
- Rotel
- Edision
- Bang And Olufsen
- Busch-Jaeger
- GBS Elettronica
- URC
Nyaste Fjärrkontroll Manualer
9 April 2025
4 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
1 April 2025
31 Mars 2025
31 Mars 2025
30 Mars 2025