VTech ErisTerminal VH6102 Bruksanvisning
Läs gratis den bruksanvisning för VTech ErisTerminal VH6102 (2 sidor) i kategorin Headset. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 6.5 recensioner. Har du en fråga om VTech ErisTerminal VH6102 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
To register a headset to a telephone
base:
NOTE
S
• You cannot register a headset if any other system
handset or headset is in use. You can only register
one headset to the telephone base at a time.
• The headset must be deregistered before
registering it to another telephone base.
• If the registration fails, you hear “Not registered”
when you press key on the headset. The ON/OFF
ON/OFF light on the headset flashes slowly and
alternately in red and blue. To reset the headset,
remove it from the headset charger and then place
it back into its charger. Try the registration process
again.
1. On the telephone base, press and MENU
then select User settings > DECT headset.
2. Lift the cordless headset out of its charging
base, and then place it back in the charger.
The light on the headset flashes quickly and
alternately in red and blue.
3. On the telephone’s DECT headset menu,
with 1. Register highlighted, press SELECT.
It takes about 60 seconds to complete the
registration process. The light on the headset
turns red when it is registered but not fully
charged, or turns blue if it is registered and
fully charged. The telephone screen displays
“Registration succeeded”.
If the registration process is successful, you
hear a dial tone when you press ON/OFF on the
headset.
Replace a headset
If you want to replace a headset or reassign the
headset to another telephone, you must first
deregister the headset from the telephone.
To deregister the headset:
1. Ensure the headset is in the charger.
2. On the telephone, press and then MENU
select User settings > DECT headset.
3. On the telephone’s DECT headset menu,
highlight 2. Deregister and then press
SELECT.
The deregistration process takes up to 10
seconds to complete. There is a confirmation
tone from the telephone base. The light flashes
slowly and alternately in red and blue when the
deregistration process completes.
If the deregistration process is successful, you
hear “Not registered” when you press ON/OFF
on the headset. The telephone screen displays
“DECT headset is deregistered”.
If the deregistration fails, you may need to:
• remove and replace the headset in the
charger and repeat the deregistration
instructions.
-OR-
• reset the headset and repeat the
deregistration instructions.
NOTE
• You cannot deregister a headset if any system
handset or headset is in use.
Position the headset
There are four earbuds and four earhooks
provided. One earbud and one earhook have
been attached to the headset.
You can choose a suitable size of earbud,
earhook and an appropriate way to position your
headset.
Replace the pre-installed earbud and
earhook:
1. Hold both sides of the earbud. Twist and pull the
earbud until it separates from the earpiece.
2. Rotate the earhook to vertical direction and
then pull the earhook until it separates from the
headset.
3. Attach a earhook, and then a suitable earbud to
the headset until they fit into place.
To wear on the right ear:
To wear on the left ear:
4. Wrap the earhook with the sponge.
Adjust the headset to wear on the ear:
• Hook the headset on your ear. Adjust the angle
of the headset until the microphone is pointing
towards your mouth. Firmly grip the headset
with one hand whenever adjusting the headset
microphone up or down.
Over-the-head band
To attach the head band to the headset:
1. Refer to Steps 1 and 2 in Replace the
pre-installed earbud and earhook section
to remove the earbud and earhook.
2. Attach the headset to
the headband. With the
headset at a vertical angle
(microphone pointing down),
insert the earpiece into the
headband.
3. Rotate the headset in a
horizontal direction until it
clicks into place.
4. Adjust the head band to fit your head. Adjust
and rotate the angle of the headset until the
microphone is pointing towards your mouth.
To remove the head band from the
headset:
1. Hold the headset with one hand and the head
band with your other hand.
2. Rotate the headset downwards to a vertical
position and then pull out the headset until it
separates from the head band.
Behind-the-neck band
By default, the ear pad on the neck band is
positioned to be worn on the right ear.
To attach the headset to the neck band:
1. Refer to Steps 1 and 2 in Replace the
pre-installed earbud and earhook section
to remove the earbud and earhook.
2. Attach the headset to the neck band. With
the headset at a vertical angle (microphone
pointing down), insert the earpiece into the
neck band.
3. Rotate the headset in a horizontal direction until
it clicks into place.
4. Place the neck band around your neck and
over your ears.
5. Adjust and rotate the angle of the headset
until the microphone is pointing towards your
mouth.
Using the headset
Make a call
1. Follow the instructions in your telephone user’s
manual for making calls.
2. Press the headset key to join the call.ON/OFF
If the telephone has a HEADSET button, you
can press the HEADSET button to switch audio
to the headset.
–OR–
1. Press the headset key to go off hook.ON/OFF
If the telephone has a HEADSET button, you
can press the HEADSET button to go off hook.
2. On the telephone, dial the number.
Answer a call
• Press ON/OFF key to answer a call.
If the telephone has a HEADSET button, you can
press the HEADSET button to answer the call.
End a call
• Press ON/OFF key or place the headset in the
headset charger.
If the telephone has a HEADSET button, you can
press the HEADSET button to end the call.
Ringer
The headset does not have an external ringer.
When there is an incoming call, the headset
earpiece rings.
Volume
• During a call, press or on the VOL+ VOL-
headset to adjust the listening volume.
Mute
The mute function allows you to hear the other
party, but the other party cannot hear you.
1. During a call, press . The headset MUTE
announces “Mute on”.
2. again to resume the conversation. Press MUTE
The headset announces “Mute off”.
Call waiting
If your service provider supports call waiting
service and call waiting has been enabled for
your phone, you hear an alert tone if there is an
incoming call while you are on another call.
• to put the current call on hold Press FLASH
and take the new call.
• to switch between calls.Press FLASH
Switch a call between a telephone’s
corded handset and a headset
(ErisTerminal SIP Desksets only)
• To switch from your phone’s corded handset
to a headset during a call, press the ON/OFF
key on the headset, and then hang up the
handset.
If the telephone has a HEADSET button, you can
press the HEADSET button to switch audio to the
headset.
• To switch from a headset to a corded handset
during a call, lift the handset. If the handset is
already off hook, press the HEADSET button,
if available.
Operating range
This cordless headset operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even
so, this headset and telephone base can
communicate over only a certain distance—which
can vary with the locations of the telephone base
and headset, the weather, and the layout of your
home or office.
If there is a call while the headset is out of range,
it may not ring, or if it does ring, the call may not
connect well when you press the key on ON/OFF
the headset. Move closer to the telephone base,
and then press key on the headset to ON/OFF
answer the call.
If the headset moves out of range during
a telephone conversation, there may be
interference.
To improve reception, move closer to the
telephone base.
General product care
Taking care of your headset
Your cordless headset contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the headset down gently. Save the original
packing materials to protect your headset if you
ever need to ship it.
Avoid water
Your headset can be damaged if it gets wet.
Do not use the headset outdoors in the rain,
or handle it with wet hands. Do not install the
headset charger near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your headset
Your headset has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Congratulations
on purchasing your new VTech product. Before
using this product, please read Important safety
instructions.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Headset overview
1 – VOL+
• Increase the headset volume.
VOL-
• Decrease the headset volume.
Flash
• While on a call, press and hold to answer
an incoming call when you receive a call
waiting alert.
2 – ON / OFF light
• On when the headset is charging.
ON / OFF key
• Press to answer or end a call.
3 – Microphone
4 – MUTE
• Mute the microphone during a call.
• When there is an incoming call, press
to silence the ringer in the earpiece
temporarily.
• Press to activate the voice-controlled
application on your connected cell phone
when idle.
5 – Earpiece
6 – Earhook
Charger overview
1 – Magnetic charging mount
• Place the headset for charging.
2 – Power jack
Lights and alert tones overview
Light status
Alert tones
Connect
NOTE
S
• Use only the adapter provided.
• The power adapter is intended to be correctly
oriented in a vertical or floor mount position.
• Charge the battery provided with or identified for
use with this product only in accordance with the
instructions and limitations specified in this manual.
Connect the charger
Connect the charger as shown below.
Install the battery
Install the battery as shown below.
NOTE
S
• Use only supplied battery.
• If the headset will not be used for a long time,
remove the battery to prevent possible leakage.
Charge the battery
Place the headset in the charger to charge. The
LED light turns on.
NOTE
S
• For best performance, keep the headset in the
charger when not in use.
• The batter y is fully charged after 3 hours of
continuous charging.
• When fully charged, the batter y provides
approximately 4 hours of talk time or 48 hours of
standby time.
Before use
Add and register a headset
Before use, each newly purchased headset
(VH6102) must be registered to a telephone
base. The headset is compatible with the
following VTech models:
• ErisTerminal
®
SIP Deskset (VSP725, VSP726,
VSP736)
• ErisStation
®
Conference Phone (VCS752).
The telephone base recognizes and counts a
headset the same as a handset.
You can register one headset to one telephone
base. If the phone already has a headset
registered, you need to deregister the headset as
described in this manual before you can register
the VH6102 headset.
Before registering:
Place the non-registered headset in the
headset charger and allow it to charge for at
least 15 minutes before registration. Remove
the headset from the headset charger. The
LED light on the headset flashes slowly and
alternately in red and blue.
ErisTerminal
®
and ErisStation
®
are registered
trademarks of VTech Communications, Inc.
BC
VH6102
DECT 6.0 accessory
cordless headset
Go to businessphones.vtech.com
to register your product for enhanced
warranty support and the latest
VTech product news.
Telephones identified with this
logo have reduced noise and
interference when used with
most T-coil equipped hearing
aids and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of the
Telecommunications Industry
Association. Used under license.
User’s manual
Red • On when the headset battery is
charging.
• Flashes every 10 seconds when
the headset battery is low and
needs charging.
Blue • Flashes twice every three seconds
when the headset is in use.
• Flashes every four seconds when
there is an incoming call.
• Flashes every 10 seconds when
the headset is out of the headset
charger and has enough charge.
Red and blue • Flashes slowly when the headset
is not registered.
• Flashes quickly when the headset
is registering to a telephone base.
Off • No battery is installed, or the
headset has run out of battery.
• The headset is powered off.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
User’s manual
f
d
e
c
b
a
a
b
One short
beep every
30 seconds
• The microphone is muted.
Two low
beeps
• Call waiting alert tone.
Three rising
beeps
• A conference call has started.
Earhook sponge Headset battery
Neck band and ear pad
Headset
Headset charger Charger adapter
Head band and ear pad
Additional earhooks and earbuds
1
2
Produktspecifikationer
| Varumärke: | VTech |
| Kategori: | Headset |
| Modell: | ErisTerminal VH6102 |
Behöver du hjälp?
Om du behöver hjälp med VTech ErisTerminal VH6102 ställ en fråga nedan och andra användare kommer att svara dig
Headset VTech Manualer
15 Juni 2025
15 Juni 2025
9 Augusti 2024
Headset Manualer
- EKids
- Aftershokz
- Elecom
- Aukey
- Geemarc
- Hama
- Xtrfy
- Kanex
- Omnitronic
- IHome
- Pioneer
- Homido
- Bigben
- OTL Technologies
- Ewent
Nyaste Headset Manualer
19 Oktober 2025
11 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
9 Oktober 2025
9 Oktober 2025
9 Oktober 2025