WyreStorm TX-SW-IW-0201 Bruksanvisning
WyreStorm
Inte kategoriserad
TX-SW-IW-0201
Läs gratis den bruksanvisning för WyreStorm TX-SW-IW-0201 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 35 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 18 recensioner. Har du en fråga om WyreStorm TX-SW-IW-0201 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
2x1 HDMI/VGA over HDBaseT™ Auto-Switching 2-Gang
In Wall Transmitter (100m/328ft)
TX-SW-IW-0201
Quickstart Guide
In the Box
1 x TX-SW-IW-0201 HDBaseT Wall Plate Transmitter
1 x 3-pin Plug-in Phoenix Connector
2 x 2pin-plug-in phoenix connectors
1 x Decorative Wall Plate with 4 screws
4 x 6-32x20mm Installation Screws
Basic Wiring Diagram
Installation
IMPORTANT! Do not connect or disconnect (hot plug) the HDMI, or
HDBaseT connections while the transmitter is powered on. Doing so may
cause damage to the transmitter or connected devices.
1. Verify that all items are included in the packaging per the list under
the In the Box section.
2. Run a Cat5/5e/6 cable from the transmitter location to the receiver
location. Terminate the cable per the HDBaseT Wiring section and
connect to the HDBT Out on the transmitter.
3. (Optional) Terminate an IR emitter or cable per the IR Wiring section
and connect to the IR Out on the transmitter. Place the IR emitter
onto the source device near the IR receiver or connect to an IR port
on the source.
4. (Optional) Terminate a cable per the RS-232 Wiring section and
connect to the RS-232 pass-through on the transmitter. Connect the
opposite end to a port on a control system.
5. Connect the opposite end of the HDBaseT cable to a WyreStorm
HDBaseT receiver, switcher, or 3rd party display device with built-in
HDBaseT receiver. Power on the receiver.
6. (Optional) If power for the transmitter is not being supplied by the
receiver via PoH, connect a 12V DC 1A power supply (not included)
to the Power In connection on the transmitter. See Power Supply
Wiring.
7. Install the TX-SW-IW-0201 in a dual-gang wall box located near the
source.
8. Connect up to 2 sources to the transmitter.
• Connect a VGA source to the VGA In on the transmitter.
• Connect an HDMI source to the HDMI In on the transmitter using
an HDMI cable from a high quality brand such as WyreStorm
Express.
9. Power on the HDBaseT receiver or connect the power supply to an
AC outlet.
A PoH compatible HDBaseT transmitter with VGA & HDMI inputs, tting into a decora 2-Gang wall box.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
TX-SW-IW-0201 Quickstart Guide | 150828
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
KEY
HDMI
HDBaseT Cat5e/6
IR TX and RX
Analog Video (VGA)
Analog Audio
HDMI from Source
VGA from Source
Audio from Source
IR Out to Source
HDBaseT Cat5e/6
HDMI to
Display
IR TX to Display
IR RX (IR to Transmitter)
TX-SW-IW-0201 Front (with wall-plate)
TX-SW-IW-0201 Rear
HDMI Source
VGA Source
4K HDMI Display
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Produktspecifikationer
| Varumärke: | WyreStorm |
| Kategori: | Inte kategoriserad |
| Modell: | TX-SW-IW-0201 |
| Vikt: | 190 g |
| Bredd: | 108 mm |
| Djup: | 106.7 mm |
| Höjd: | 25 mm |
| Produktens färg: | Svart |
Behöver du hjälp?
Om du behöver hjälp med WyreStorm TX-SW-IW-0201 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad WyreStorm Manualer
3 April 2025
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
Inte kategoriserad Manualer
- Claypaky
- Little Tikes
- Iiyama
- Lumu
- Dobot
- Dnt
- Lofrans
- IStarUSA
- Festo
- OJ ELECTRONICS
- Bella
- Bearware
- EMOS
- Livall
- Hozelock
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025