Zempire Drift Bruksanvisning

Zempire tält Drift

Läs gratis den bruksanvisning för Zempire Drift (2 sidor) i kategorin tält. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 8.5 recensioner. Har du en fråga om Zempire Drift eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

2. Assemble the 6 pole sections.

Ensure that the poles are inserted

fully in tho the steel connectors.

6. Peg out the four corners

firmly ensuring that the floor

sits at flat as possible.

7. Peg out all the remaining peg

points around the tent. Firmly peg

out the rear guy rope attached to

the large fin at the rear of the tent

at a 45o angle.

9. Pull the fly over the tent

and connect the SR buckle sewn

onto the fin at the rear of the

tent. Attach the hooks onto the

loops sewn around the pole

sleeves.

10. Peg out all the guy ropes. Try to

have guy ropes at a 45o angle to the

ground. Also peg out the lower draft

vents on each side of the tent.

3. Thread the RED poles through the

pole sleeves that run diagonally across

the centre of the tent. Tension the poles

inserting the pins located directly under-

neath each pole sleeve into the ends of

the poles. It may be easier to have

someone to support the crossover of the

poles during this step.

PITCHING INSTRUCTIONS - DRIFTairflowseries

4. Thread the BLUE pole through the

front and the pole through the GREEN

rear pole sleeves that run across the

centre of the tent. Tension the poles

inserting the pins located directly under-

neath each pole sleeve into the ends of

the poles. .

5. Thread the YELLOW pole

through the pole sleeve at the rear

of the tent. Tension the poles insert-

ing the pins located at the rear

corners of the tent.

8. Thread the remaining think

(4mm) pole through the pole

sleeve underneath the vent cover

above the door and insert the

pole ends into the small pockets

on each side.

1. Clear your site making sure there are no

sharp objects. Try to get a site that is as flat

as possible. Stretch out the tent with the

door facing the front.

pitching instructions

DRIFTairflowseries

Freedom Zempire is proud to be a

100% New Zealand owned and

operated business.

For more information about this

and other great products we offer

please visit our website.

WWW.FREEDOMCAMPING.COM

1. Ensure guy ropes are pegged out at all times during use

2. Never pack your tent away wet. If you must take your tent down when

wet, ensure that you dry you tent completely as soon as possible to

prevent mildew forming.

3. If mildew does form on your tent wash off pours with warm water and a

soft brush to prevent further growth. Do not use detergents.

4. Do not use an open flame inside your tent. The fabric has been treated

with a fire retardant but is in no way fire proof

5. Clean all pegs and poles before storing

6. If your poles do break, use the repair sleeve to cover over the broken

section. Once you have returned contact your local retailer for a

replacement pole section.

PITCHING INSTRUCTIONS - DRIFTairflowseries

11. For extra warmth and privacy

you may decide to attach the

inner inside the tent. Lay out the

inner inside the tent with the

door facing the front and the

floor facing downwards. Attach

the corner male buckles to the

female buckles sewn into the

inside rear corners of the tent.

Connect the toggles through the

corresponding rings sewn on the

tent working your way front the

rear to the front of the inner. Peg

down the front of the inner and

cover.

Produktspecifikationer

Varumärke:	Zempire
Kategori:	tält
Modell:	Drift
Vikt:	960 g
Bredd:	130.9 mm
Djup:	111.8 mm
Höjd:	165.1 mm
Förpackningens vikt:	1180 g
Förpackningens bredd:	155 mm
Djuppackning:	167 mm
Förpackningshöjd:	232 mm
Snäll:	Koeler
Ljudnivå (låg hastighet):	6 dB
Ljudnivå (hög hastighet:	31 dB
Maximalt luftflöde:	53.38 cfm
Färg på belysningen:	Blue, Green, Red
Rotationshastighet (max):	1800 RPM
Rotationshastighet (min):	650 RPM
Kvantitet per (yttre) huvudkartong:	8 stuk(s)
Belysning LED:	Ja
Lämplig plats:	Processor
Strömförbrukning (typiskt):	3.6 W
Harmoniserad systemkod (HS):	84733080
Spänningsklassificering:	12 V
Nominell nätspänning:	0.3 A
Maximalt lufttryck:	1.65 mmH2O
Finmaterial:	Aluminium
Antal värmerör:	4
Matventilator (bxdxh):	120 x 120 x 165.1 mm
Värmerörs diameter:	6 mm
Fläktkontakt:	4-pin
Kylfläns vikt:	820 g
Mean Time To Failure (MTTF):	40000 uur
Säkerhetsströmstyrka:	0.37 Ah