Zenit ZVSH-350 Bruksanvisning
Zenit
Orbital slipmaskiner
ZVSH-350
Läs gratis den bruksanvisning för Zenit ZVSH-350 (10 sidor) i kategorin Orbital slipmaskiner. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 2.5 recensioner. Har du en fråga om Zenit ZVSH-350 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/10
InstructIon manual
FInIshIng sander
gm-350
3
GENERAL SAFETY PRECAUTIONS
WARNING! When using electric tools, basic safety precautions should always be fol-
lowed to reduce the risk of re, electric shock and personal injury, including the following.
Read all these instructions before operating this product and save these instructions.
For safe operations:
1. Keep work area clean. Cluttered areas and benches invite injuries.
2. Consider work area environment. Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work area well lit. Do not use power tools where
there is risk to cause re or explosion.
3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces.
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children and inrm persons away. Do not let visitors touch the tool or exten-
sion cord. All visitors should be kept away from work area.
5. Store idle tools. When not in use, tools should be stored in a dry, high or locked up
place, out of reach of children and inrm persons.
6. Do not force the tool. It will do the job better and safer at the rate for which it was
intended.
7. Use the right tool. Do not force small tools or attachments to do the job of a heavy
duty tool. Do not use tools for purposes not intended.
8. Dress properly. Do not wear loose clothing or jewelry; they can be caught in moving
parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear
protecting hair covering to contain long hair.
9. Use eye protection. Also use face or dust mask if the cutting operation is dusty.
10. Connect dust extraction equipment. If devices are provided for the connection of
dust extraction and collection facilities ensure these are connected and properly used.
11. Do not abuse the cord. Never carry the tool by the cord or yank it to disconnect it
from the receptacle. Keep the cord away from heat, oil and sharp edges.
12. Secure work. Use clamps or a vise to hold the work. It is safer than using your hand
and it frees both hands to operate tool.
13. Do not overreach. Keep proper footing and balance at all times.
14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and changing accessories. Inspect tool cords
periodically and if damaged, have it repaired by authorized service center. Inspect extension
cords periodically and replace, if damaged. Keep handles dry, clean, and free from oil and
grease.
15. Disconnect tools. When not in use, before servicing, and when changing accessories
such as blades, bits and cutters.
16. Remove adjusting keys and wrenches. Form the habit of checking to see that keys
and adjusting wrenches are removed from the tool before turning it on.
17. Avoid unintentional starting. Do not carry a plugged in tool with a nger on the
Produktspecifikationer
| Varumärke: | Zenit |
| Kategori: | Orbital slipmaskiner |
| Modell: | ZVSH-350 |
Behöver du hjälp?
Om du behöver hjälp med Zenit ZVSH-350 ställ en fråga nedan och andra användare kommer att svara dig
Orbital slipmaskiner Zenit Manualer
24 Juli 2024
Orbital slipmaskiner Manualer
Nyaste Orbital slipmaskiner Manualer
18 Oktober 2024
13 Oktober 2024
11 Oktober 2024
9 Oktober 2024
1 Augusti 2024
1 Augusti 2024
30 Juli 2024
29 Juli 2024
29 Juli 2024
29 Juli 2024