4ms Stereo Triggered Sampler Bruksanvisning

4ms Inte kategoriserad Stereo Triggered Sampler

Läs gratis den bruksanvisning för 4ms Stereo Triggered Sampler (24 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 10.5 recensioner. Har du en fråga om 4ms Stereo Triggered Sampler eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/24

Stereo Triggered Sampler

4ms Company

User Manual 1.0 – August 16, 2017

for f irmware v1.0

The Stereo Triggered Sampler is a high fidelity, two-channel stereo audio recorder and playback module. The

STS can record high quality stereo WAV files while simultaneously playing two different stereo files. A maximum of

600 samples can be loaded at one time from the removable/swappable microSD card, in a variety of formats up to

96kHz/32-bit/stereo WAV. All sample parameters (1V/oct pitch, sample file selection, length, and start position) are

CV controllable, and trigger jacks for play, record, and reverse allow for synchronization. On-board editing tools

allow you to set loop/trim points and gain, as well as assigning samples to banks and slots.

•Two independent stereo playback channels can play any of 600 samples simultaneously

•Recording channel creates stereo WAV files directly onto microSD Card for immediate use

•Extremely low noise, high fidelity design

•Plays a variety of WAV files up to 32-bit/96kHz

•Intelligent file system makes loading large sample libraries easy by organizing banks into folders

•CV and controls for 1V/oct tracking, Start Position, Length, Sample selection, Reverse and Play

•Trim samples and set Loop points, adjust gain, and re-organize banks and sample slots on the fly.

•Includes microSD card with Sample Pack, SD adaptor, 10-to-16 pin power cable and M3 screws

Table of Contents

Setting up your Stereo Triggered Sampler

1. Remove the Stereo Triggered Sampler (STS) from the box and anti-static bag. The RAM chip on the STS may

be damaged by static electricity; take care not to touch the circuit board.

2. Connect the free end of the power cable to a 16-pin Eurorack power header on your power supply distribution

system, with the red stripe towards to the -12V. The other end of the power cable is a

10-pin connector which should already be connected to the STS so the red stripe on

the power cable is orientated towards the bottom of the module (the bottom is marked

by a white stripe and the word “POWER”). Note: The STS is reverse-polarity

protected, but other modules being incorrectly connected could damage anything on

the power bus.

3. Backup your microSD card before you first power the STS on! We recommend

you perform a full backup of the microSD card by using a computer (use the included

SD card adaptor if needed). This will be useful if the card ever becomes damaged or

you wish to restore the STS to the original factory settings and samples.

4. Securely screw the STS to the rails of your case. Power the system on.

5. Begin with Tutorial 1: Basic Playback on page 5 of this manual.

Never remove the microSD card when the light is on!Busy !

Setting up your Stereo Triggered Sampler 2! ".............................................................

Overview 3! "................................................................................................................

Electrical and Mechanical Specifications 4! "..............................................................

Tutorial 1: Basic Playback 5! "......................................................................................

Tutorial 2: Navigating Banks 6! "..................................................................................

Stereo/Mono Mode 8! "................................................................................................

Channel Playback Volume 8! ".....................................................................................

Tutorial 3: Recording Samples 9! "...............................................................................

Tutorial 4: Loading Files onto the microSD Card 10! ".................................................

Sample List HTML file 12! "..........................................................................................

Edit Mode: Gain, Loop/Trim points 13! "......................................................................

Saving and Reverting 14! "...........................................................................................

Copying 14! "................................................................................................................

Tutorial 5: Creating Slices 15! "....................................................................................

Example Patch: Sequencing the STS 16! "..................................................................

Example Patch: Granular Scrubbing 17! "...................................................................

Recording the STS Output as a New Sample 18! ".....................................................

Example Patch: Clock Sync and Shifting Ping-Pong Loops 18! "...............................

Assigning Samples to Banks and Slots 19! "...............................................................

System Mode 21! ".......................................................................................................

1V/OCT Tracking Compensation 21! ".........................................................................

Rebuilding the Index File 21! ".....................................................................................

Updating Firmware (Audio Bootloader) 22! "...............................................................

microSD Card Specifications 23! "...............................................................................

File Formats 23! ".........................................................................................................

Chart of All Button Features 24................................................................................!

Page of  2 24

Overview

• Up to 600 samples loaded at one time (10 samples per bank)

• Includes a microSD card with over 200 samples

• Extremely quiet, low noise and low jitter design

• Stereo or Mono operation:

•Stereo mode: Two stereo files are mixed and played through the L and R output jacks (L+L and R+R)

•Mono mode: Each file is mixed to mono and output through the channel's output jack (L+R and L+R)

• Firmware can be updated by playing an audio file into the STS

Two independent playback channels:

• Each channel outputs in mono or stereo through the shared L/R jacks

• Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample

•When Length is set to “All”, the Play button starts/stops the sample (set in System Mode, see p.21)

•Sample CV/knob: select which sample within the channel's bank

• 1V/OCT CV and Pitch knob: playback pitch (-10 to +4.3 octave range)

• Start Pos CV/knob: position in the sample to begin playback (loop start point)

•Length CV/knob: playback time (loop end point)

•Length knob at max: entire file is played

•Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)

•Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if

playing Reverse)

•Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)

• Reverse button/jack: toggles forward/backwards

•Bank button: selects channel's bank

and turn the knobs for fast selection of bank Tip: Hold Bank Sample

• Edit button allows basic on-board editing features:

•Set loop/trim points with Scrub Start and Scrub End

•Set (boost/cut from 10% to 500%) Gain

•Re-organize samples with Next File

•Move samples around within a bank

•Assign files from any folder on the microSD card into any sample slot (sub-folders are ignored)

•Copy sample to multiple slots, each with their own loop/trim/gain settings

• Reverse+Start Pos button/knob combo allows for setting volume of each channel independently.

• Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)

• microSD Card is hot-swappable when light is off: no power-down required to change cards Busy

•Samples that are pre-loaded into memory can continue playing while card is removed

Recording channel:

• Stereo recording can be simultaneous to operation of playback channels

•Easily record output of sample playback, “bouncing” a play session into a new sample file

• Recording initiated by button or trigger

• Monitor mode lets you check the signal before starting a recording

• Record into any sample slot in any bank

•Every recording is saved as a WAV file on the microSD Card and can be played back instantly

•Edit features allow you to manually browse all the takes, and assign them to banks/sample slots

• Recording can be disarmed to prevent accidental recordings

• 44.1kHz/24-bit stereo or 16-bit stereo recording, selectable in System Mode

• “Unlimited” recording time (records continuously until card is full)

•256GB card = 18 days of continuous recording (432.9 hours)

•Long recordings are split into 4GB WAV files

Page of  3 24

Produktspecifikationer

Varumärke:	4ms
Kategori:	Inte kategoriserad
Modell:	Stereo Triggered Sampler
Färg på produkten:	Black, Metallic, Purple
Vikt:	340 g
Bredd:	93 mm
Djup:	80 mm
Höjd:	140 mm
Snäll:	Koeler
Ljudnivå (hög hastighet:	30 dB
Förpackningsmått (BxDxH):	182 x 118 x 192 mm
Material:	Aluminium
Maximalt luftflöde:	43 cfm
Antal fans:	1 ventilator(en)
Spännande:	12 V
Rotationshastighet (max):	2000 RPM
Medeltid mellan fel (MTBF):	40000 uur
Anslutning(ar):	3-pin
Lämplig plats:	Processor
Kompatibla processorer:	Niet ondersteund
Strömförbrukning (typiskt):	2.16 W
Ventilator diameter:	92 mm
Nominell nätspänning:	0.17 A
Lagerteknik:	Gegroefd
Processorsocklar som stöds:	Socket AM2, Socket AM2+, Socket AM3+, Socket FM1
Maximalt lufttryck:	2.2 mmH2O
Kylflänsens mått (B x D x H):	90 x 51 x 140 mm