Airtronics VG400 Bruksanvisning
                    Airtronics
                    
                    Radiostyrning
                    
                    VG400
                
                                
    Läs gratis den bruksanvisning för Airtronics VG400 (7 sidor) i kategorin Radiostyrning. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 5.5 recensioner. Har du en fråga om Airtronics VG400 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
                        Sida 1/7
                    
                    
                    
 1
VG400 and VG600 FM 4/6 Channel Systems 
SECTION I Safety First for Yourself and Others. 
SECTION II Federal Licensing Requirements 
and Special Operating Standards for 
Model Airplanes 
SECTION III System Features 
SECTION IV Unpacking and setting up your 
AIRTRONICS VG400 or VG600 
Radio Control System 
SECTION V Operation Adjustments 
NOTE:  FOR BATTERY CHARGING 
INFORMATION AND INSTRUCTIONS ON 
LEARING TO USE YOUR AIRTRONICS RADIO 
SYSTEM, PLEASE SEE THE AIRTRONICS 
RADIO OPERATION AND INSTALLATION 
INSERT. 
THANK YOU FOR SELECTING AIRTRONICS 
We appreciate your purchase of this new AIRTRONICS 
VG400 or VG600 Radio System. 
These instructions are intended to acquaint you with the 
many unique features of this modern, state-of-the-art 
equipment. Please read them carefully so that you may 
obtain maximum success and enjoyment from its 
operation 
TRANSMITTER FEATURES AND FUNTIONS 
The AIRTRONICS VG400/VG600 Radio Control Systems are 
primarily intended for the flying of fixed wing model aircraft. 
1. Retractable antenna 
2. LED Scale Voltage Display 
3. Control stick, horizontal-ailerons, vertical-elevator 
(mode 2) Vertical-throttle (Mode 1) 
4. Trim lever, elevator (Mode 2); throttle (Mode1) 
5. Trim lever ailerons 
6. Name Plate 
7. Power Switch 
8. Trim lever throttle (Mode 2); elevator (Mode 1) 
9. Trim lever rudder 
10. Control stick, horizontal-rudder, vertical-throttle 
(Mode 2) Vertical-elevator (Mode 1) 
11. Neck strap connecting hook 
12. Servo reverse switches 
13. Retract aux Channel (VG600 Only) 
14. Trainer button 
15. Carrying handle 
16. 3 position aux channel flap switch (VG600 Only) 
17. Throttle High and Low End point adjustments 
18. Ail, Elev, Rud, Flap Servo Travel Adjusters 
(VG600 Only) 
We ask that you pay particular attention to the design of 
the transmitter. Notice that it has been engineered for 
the most natural and precise control of your choice of 
flying models. 
Be certain to read all of the material in this manual, as 
well as the Operation and Installation insert. 
SECTION I 
SAFETY FIRST FOR YOURSELF, FOR OTHERS 
AND FOR YOUR EQUIPMENT. 
“Safety First” is more than just a slogan when operating 
radio control models. Thus, we urge, especially with 
respect to radio controlled aircraft that: 
FOR YOUR SAFETY: 
Recognize that radio controlled models are not harmless 
toys and can be dangerous missiles if carelessly or 
improperly flown.  You are responsible because the 
reliability and safe operation of the radio equipment is 
largely dependent upon its proper installation and 
utilization. 
THEREFORE, INSTALL YOUR RADIO CONTROL 
SYSTEM CORRECTLY AND BE CERTAIN YOU 
CAN FLY WELL ENOUGH TO CONTROL YOUR 
AIRCRAFT UNDER ALL CONDITIONS. 
POWER
ON
FULLMIDLOW
(1) (2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)(18)
(17)
(12)
Produktspecifikationer
| Varumärke: | Airtronics | 
| Kategori: | Radiostyrning | 
| Modell: | VG400 | 
Behöver du hjälp?
Om du behöver hjälp med Airtronics VG400 ställ en fråga nedan och andra användare kommer att svara dig
Radiostyrning Airtronics Manualer
                        
                         21 Juli 2024
                        
                    
                                                            Radiostyrning Manualer
Nyaste Radiostyrning Manualer
                        
                         17 Oktober 2024
                        
                    
                                                            
                        
                         16 Oktober 2024
                        
                    
                                                            
                        
                         14 Oktober 2024
                        
                    
                                                            
                        
                         15 September 2024
                        
                    
                                                            
                        
                         14 September 2024
                        
                    
                                                            
                        
                         14 September 2024
                        
                    
                                                            
                        
                         14 September 2024
                        
                    
                                                            
                        
                         14 September 2024
                        
                    
                                                            
                        
                         14 September 2024
                        
                    
                                                            
                        
                         14 September 2024