ALM Boss Bow Two -027 Bruksanvisning
ALM
Inte kategoriserad
Boss Bow Two -027
Läs gratis den bruksanvisning för ALM Boss Bow Two -027 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 11.5 recensioner. Har du en fråga om ALM Boss Bow Two -027 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
The Boss Bow Two is an 8 way bidirectional voltage controlled switch with 3 different control modes for routing CV or audio signals around a
system. Address mode allows for instant routing manually via the offset or external control voltage, step mode sequentially advances I/O fol-
lowing signal at the clock input and the strobe mode combines the two, holding the addressed position until the next clock pulse. The unique
features and flexibility of the ‘BB2’ allow for a wide range of potential patches to be created.
MODES
Current mode is indicated by its associated LED.
Step : Advances one by one through the I/Os with every pulse at
the clock input. The offset control or CV input sets the direction of
the stepping with the reset input returning back to the first I/O.
Strobe : Selects an I/O based on the voltage level or offset posi-
tion with respect to the clock input. Upon receiving a high gate,
selection will move to the I/O matching the current voltage level
and will hold that position until the next pulse.
Address : Selects an I/O based on the voltage level or offset posi-
tion. Address will immediately change I/Os and sweeps through
all jacks. Rising voltage moves the selection downward with
falling voltage going back to the top.
EIGHT MAPPABLE I/Os
Inputs or outputs connecting a signal route to or from the I/O jacks
on either side. I/Os accept both CV and audio. I/Os are switched by
the control section with each LED indicating the current connection.
MODE BUTTON
Switches the current operating
mode of the BBT from step to
strobe to CV address mode.
SINGLE SIGNAL I/O
Input or output connecting to or
from the I/O jacks on the right
side. Accepts both CV and audio.
CLOCK / RESET INPUTS
A clock signal advances through
I/Os in step mode and guides
CV selection in strobe mode.
Reset will return the BBT back
to the first I/O upon receiving
a gate signal in step mode and
disables / enables the switch in
strobe and address modes.
BIPOLAR OFFSET
Adds or subtracts voltage from
the control signal. Combines
with control input for manual
control and adjustment.
CONTROL INPUT / ATTENUATOR
Voltage at this input selects
an I/O in address and strobe
modes. In step mode positive
voltage advances downwards
and negative voltage advances
upwards.
Use the attenuverter and offset
to dial in desired CV response.
http://busycircuits.com/alm027
TECHNICAL SPECIFICATIONS
Power: +12V 40ma / -12V 10ma
Size: 8HP
Depth: 38mm
ALM027 /
Boss Bow Two
LIMITED WARRANTY
From the date of manufacture
this device is guaranteed for a
period of 2 years against any
manufacturing or material
defects. Any such defects will
be repaired or replaced at the
discretion of ALM. This does not
apply to;
•Physical damage arising from
mistreating (i,e dropping, sub-
merging etc).
•Damage caused by incorrect
power connections.
•Overexposure to heat or direct
sunlight.
•Damage caused by inappropri-
ate or misuse.
•Use of incorrect or non official
firmware
No responsibility is implied or
accepted for harm to person
or apparatus caused through
operation of this product. By
using this product you agree to
these terms.
SUPPORT
Need help? Email your questions
to help@busycircuits.com
For additional info, downloads
and firmware updates please
visit the ALM website at
busycircuits.com
Follow @busycircuits on Twitter
and Instagram for news, tips and
ideas.
Visit ‘ALM TV’ on youtube.com
for module video tuorials and
demos.
Module Installation
With your modular synth
powered connect the 10 pin off
end of the supplied standard
eurorack power connector cable
to the 10 pin power connector on
the rear of the module.
The red stripe on the cable
should be orientated to match
the text ‘RED’ marked on the
rear of the module near the
power connector (this is -12V).
Connect the other 16 pin end of
the cable to your eurorack bus
board (Refer to your bus board
documentation for the correct
orientation).
You are now safe to power up
your modular synth. If the mod-
ule fails to power up check you
have the power cable correctly
orientated and have carefully
read this manual.
ALM027 manual version: 0.1
Input
2
1
Outputs Output Inputs
4
3
6
5
8
7
2
1
4
3
6
5
8
7
Boss Bow Two
Boss Bow Two
Reset
I/OI/O
-|+
Offset
Clock
Mode
Address
Strobe
Step
Control
Produktspecifikationer
| Varumärke: | ALM |
| Kategori: | Inte kategoriserad |
| Modell: | Boss Bow Two -027 |
Behöver du hjälp?
Om du behöver hjälp med ALM Boss Bow Two -027 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad ALM Manualer
18 September 2024
18 September 2024
18 September 2024
17 September 2024
11 September 2024
11 September 2024
9 September 2024
5 September 2024
5 September 2024
5 September 2024
Inte kategoriserad Manualer
- Skaarhoj
- Fitbit
- BirdDog
- Eminent
- Bauhn
- Apantac
- Naxa
- Brainstorm
- Kemo
- Jilong
- PTZ Optics
- Antari
- My Arcade
- Eligent
- Eliminator Lighting
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025