ALM MCO -021 Bruksanvisning
ALM
Inte kategoriserad
MCO -021
Läs gratis den bruksanvisning för ALM MCO -021 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 8.5 recensioner. Har du en fråga om ALM MCO -021 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
The ‘MCO’ is a compact digital oscillator. It features a main ‘morphing’ wavetable output, an additional copy of this output with overlaid vari-
able pulse segments (ala Alpha Juno style saw wave pwm) and a sub square wave output an octave down to the main output. The waveform
and pulse segment width can be both directly and voltage controlled. The pulse segment distribution can also be voltage controlled via the
‘type’ input. Expect an early 90s slightly crunchy digital type sound (ala Ensoniq, Kawaii Kx synths) rather than something striving for perfect
analog emulation.
WAVE CONTROL AND INPUT
Selects the output waveform for both the ‘pulse’ and main audio
outputs.
Output blends between 10 different waveforms which are;
noise > tri > saw > sine > bell > organ > ‘4 oct’ > organ > voice > pulse
TYPE INPUT
An applied voltage increases the number and arrangement of pulse
segments used on the pulse output. 0 - 5V range.
FREQUENCY CONTROLS
Sets the base frequency for the oscillator output. The v/oct input is
added to this.
The main control knob sweeps approx 6 octaves.
PWM CONTROL AND INPUT
Alters the duty cycle of the
overlaid segments present in the
Pulse output.
Input expects 0-5V. At max 5v
(fully clockwise knob) no PWM
is present - i.e duty cycle 100%.
Input voltage is added to the
PWM knob position offset.
V/OCT INPUT
Sets the output frequency. Fol-
lows 1 volt per octave standard.
Frequency range is approx 10
octaves 12hz to 14Khz.
Expect aliasing at higher
frequencies (top 3-4 octaves).
SYNC INPUT
In the presence of an input
waveform rising edge the output
waveform phase is reset.
OUTPUTS
Out - main audio output - Waveform from selected wave control
(approx +/-8v)
Pulse - As the main output but with pulse width segments superim-
posed on to it.
Sub - A 50% duty cycle pulse wave an octave lower than main out.
(approx +/-8v)
http://busycircuits.com/alm021
TECHNICAL SPECIFICATIONS
Power: +12V 40ma / -12V 15ma
Size: 6HP
Depth: 38mm
Resolution: 16Bit/48Khz with
AKM codec.
ALM021 / MCO
Limited Warranty
From the date of manufacture this
device is guaranteed for a period of 2
years against any manufacturing or
material defects. Any such defects
will be repaired or replaced at the
discretion of ALM. This does not
apply to;
•Physical damage arising for mis
treating (i,e dropping, submerging
etc).
•Damage caused by incorrect power
connections.
•Overexposure to heat or direct
sunlight.
•Damage caused by inappropriate or
misuse.
•Use of incorrect or non official
firmware
No responsibility is implied or
accepted for harm to person or
apparatus caused through operation
of this product. By using this product
you agree to these terms.
Support
Need help? Email your questions to
help@busycircuits.com
For the latest news, additional info,
downloads and firmware updates
please visit the ALM website at
http://busycircuits.com and follow
@busycircuits on Twitter and Insta-
gram.
Module Installation
With your modular synth
powered connect the 10 pin off
end of the supplied standard
eurorack power connector cable
to the 10 pin power connector on
the rear of the module.
The red stripe on the cable
should be orientated to match
the text ‘RED’ marked on the
rear of the module near the
power connector (this is -12V).
Connect the other 16 pin end of
the cable to your eurorack bus
board (Refer to your bus board
documentation for the correct
orientation).
You are now safe to power up
your modular synth. If the mod-
ule fails to power up check you
have the power cable correctly
orientated and have carefully
read this manual.
V/OCT Tracking Calibration
Calibration is performed by carefully
adjusting the trimmer on the back of
the module. Apply 1V to v/oct input,
and tune the oscillator via front panel
controls to C1. Next change the input
voltage to 3V and now adjust trimmer
on reverse until you get C3. You may
need to go back and forth and repeat
the process a couple of times for best
results.
You should expect good tracking over
at least 5 octaves. Note the module
ships pre-calibrated.
ALM021 manual version: 0.1
Sub
PWM
Wave
Freq
OutPulse
Sync
V/Oct
PWM Type Wave
Produktspecifikationer
| Varumärke: | ALM |
| Kategori: | Inte kategoriserad |
| Modell: | MCO -021 |
Behöver du hjälp?
Om du behöver hjälp med ALM MCO -021 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad ALM Manualer
18 September 2024
18 September 2024
18 September 2024
17 September 2024
11 September 2024
11 September 2024
9 September 2024
5 September 2024
5 September 2024
5 September 2024
Inte kategoriserad Manualer
- QUIO
- Kaiser Fototechnik
- XFX
- Applico
- 3Doodler
- Viridian
- AutoParkTime
- Blizzard
- Nibe
- Milectric
- Tascam
- Proaim
- Premier Mounts
- Enttec
- ACCU-CHEK
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025