AMX DXFP-RX-4K60 Bruksanvisning

Läs gratis den bruksanvisning för AMX DXFP-RX-4K60 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 13 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 8 recensioner. Har du en fråga om AMX DXFP-RX-4K60 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

QUICK START GUIDE

DXLink™ Fi4K60 HDMI ber Transmitter/Receiver

Mounting Options (Rack Trays and Mounting Brackets)

The DXFP-TX-4K60 and DXFP-RX-4K60 can be mounted using V Style Surface Mounting

Brackets, V Style Single Module Pole Mounting Kit, or NMX-VRK V-Style Rack Shelf.

For details, see www.amx.com

IMPORTANT: When mounting under a surface, the module should be mounted upright and

lowered in the mounting bracket slots to provide an airflow gap between the surface and

the vent holes. If not using V Style brackets, be sure to leave a gap between the top of

the unit and the surface for heat to escape.

1 2 34

ON

IDUSB MODE

DIP Switch Toggles – Default OFF (for Auto-setup, see next page)

Before installing the units, find the scenario you are using in the table below and set the

DIP switch toggles accordingly. Toggle #4 is reserved for future functionality.

For standalone pair upgrades, set Toggles #1-2-3 to ON and connect one unit to Controller.

** In standalone setup using NetLinx control of DXLink serialR ports, only one of the /I

DXLinkunits should be connected to network (e it with #1 Toggle enabled). fiberth un

COMMON SCENARIOSTOGGLES

Standalone Setup1 - 2 - 3

AV signals only (plus serial/IR passthrough)OFF - OFF - OFF

AVith Ethernet passthrough to networked deviceplus serial/IR w (

passthrough)*

ON - OFF - OFF

AV with NetLinx control of TX/RX unit and serial/IR ports**ON -N -N O O

AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet

passthrough to network device*

ON -N -N O O

Switcher Setup (TX/RX with Enova DGX/DGX 100 Series Switcher)1 - 2 - 3

AV signals only OFF - OFF - OFF

AV with Ethernet passthrough to networked deve*ON - OFF - OFFic

AV with NetLinx control of TX/RX unit and serial/IR portsOFF - OFF - ON

AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet

passthrough to network device*

ON - OFF - ON

•Endpoint Mode (Switcher) – connect one or more to a switcher with an integrated

•Endpoint Mode (Standalone) – connect TX/RX pair direy to each other with onectl

connected to a inx Central Controller via LAN or directly to Controller.NetL

•Extender Mode (Standalone) – connect TX/RX pair directly to each other.

These Modules support InstaGate Pro® and SmartScale® Technology.

Thecontains Hardware Reference Manual - DXLink Fiber Transmitter/Receiver 4K60

complete documentation (including full specifications and supported input and output

resolutions)for details, see www.amx.com.;

System upSet

TDXFP-TX-4nd DXFP-RX-4orkith thasupDXLinkhe K60 a K60 w wa switcher t ports

Technologor s stand-alone transmit udio, ideo ndsignals. he y aa pair to ava control T

Transmireceives ud o ndeo the source nd transmits oth udio tter aia vidfrom HDMI a ba

andle. This DXLincairectly video over the fiber optic cabk fiber optic ble can be connected d

to DXLineceiver or to DXLininput on DXLink switcher where it can be a k fiber ra k fiber a

routed to a DXLinoutput andconnectedto DXLineceiver. The DXLin k fiber a k fiber rk fiber

receier converts the DXLininput to HDMI andnalogudio outputs. On the v k fiber a a

transmitter, stereo e ovedaudio connections arprid as suplemental input. the a paudio Both

t rransmitter the and eceiver suport -2or serial tatransfer, IR, Ethernet.pRS32 f da USB, and

FI. 1 GDIP WITCH STOGGLES ENABLE/DISABLE ECIAL UNCTIONALITYSPF

Ov viewer

The DXFP-TX-4K60 and DXFP-RX-4K60 transmit HDMI, audio, USB and control over

fiber optic cableThe TX also has an HDMI loop out. DXLink ber odules can be set . fi m

up in one of three ways:

FIG. 3

HDMI IN

Fiber optic cable

HDMI OUT

Source DeviceDestination Device

DXLINK FIBER TX AND RX AS EXTENDER SOLUTION

FIG. 2

DXLINK Fiber Transmitter

DXLINK Fiber Receiver

HDMI INFiber optic cable

Fiber optic cableHDMI OUT

Destination Device

DXLINK Fiber

Output Board

LAN 100/1000

Source Device

AC

DC

FLT

AC

DC

FLT

DXLINK Fiber

Input Board

DXLINK FIBER TX AND RX AS ENDPOINTS WITH COMPATIBLE DXLINK FIBER EQUIPMENT

F

IG. 4

ICS LAN 10/100 Port

The ICS LAN 10/100 port uses twisted pair cable. FIG. 4 shows the LEDs for this port.

ICS LAN (RJ45) PORT

On - Speed status is 100 Mbps

Off - Speed status is 10 Mbps

Yellow LED:

On - Link status is active

Off - Link status is not active

Green LED:

FIG. 5 FIBER OPTIC TRANSCEIVER MARKED BLACK (MULTIMODE)

Latch and/or label color

Dustg plu

SFP+ = enhancesmall form-factord

pluggableoptic transceiver ratedfiber

at0 s transmissionta rate. 1Gbp da

Fiber Optic Transceivers

The DXLink Fiber Transmitters and Receivers use SFP+ fiber optic transceivers. Fiber

optic transceivers are self-contained modules that send and receive optical signals over

fiber cable. DXLink SFP+ fiber optic transceivers is multimode and must be wired with

the corresponding cable type. Multimode transceivers support bidirectional and

unidirectional communication.

Attaching Signal, Transport, and Control Cables

Important Cabling Requirements and Considerations

•

•LC Duplex conforming to ANSI TIA-EIA 604-10 (FOCIS 10A)

•DXLink Fiber multimode transceivers use OM3 50/125 μm multimode fiber optic

cable type over distances of up to 984 feet (300 m)*

•Do not create a network (Ethernet) loop. A network loop is created when the

enclosure and one or more of its DXLink Fiber units connect to a common LAN.

Fiber optic cable with LC termination for snap coupling with SFP+ transceivers

* Connect ICS LAN port of DXLink fiber unit to network device (e.g., laptop, IP controlled

projector, ICSLan Device). In standalone setup, connect ICS LAN port of other DXLink

unit to network.

*Cable quality is a determining factor for the maximum length of cable runs.

WARNING：DXLink Fiber units use laser transceiver, which are Class 1 Eye Safe per

IEC 60825-1/CDRH requirements. While the Class 1 category indicates that the invisible

laser used is safe, we recommend avoiding direct eye exposure when using any optical

fiber products (See OSHA directive referenced in the “Hardware Reference Manual”).

DXLINK Fiber TransmitterDXLINK Fiber Receiver

Controller.

Produktspecifikationer