AMX Sereno NMX-VCC-1000-WM Bruksanvisning
AMX
Inte kategoriserad
Sereno NMX-VCC-1000-WM
Läs gratis den bruksanvisning för AMX Sereno NMX-VCC-1000-WM (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 8.5 recensioner. Har du en fråga om AMX Sereno NMX-VCC-1000-WM eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
QUICK START GUIDE
NMX-VCC-1000-WM Sereno™ Camera Wall Mount
© 2015 Harman. All rights reserved. ENZO. AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks of HARMAN.
Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/
Last Revised: 11/04/2015
93-3211-11 REV: B
Overview
The NMX-VCC-1000-WM Sereno camera wall mount (FG3211-11) allows the Sereno
camera to be mounted to a variety of surfaces. Once the mount is installed, the
Sereno camera is easily attached to it via integrated strong rare earth magnets. The
magnets also enable the base to be attached to metallic surfaces without permanent
fasteners and will support the weight of the Sereno video camera. The Sereno wall
mount kit includes the following items:
• Magnetic wall mount which houses two rare earth magnets
• Two #8 counter-sunk screws to permanently attach the base to a wall
• Two plastic wall anchors for sheet rock installations
Installation
The following procedures describe the different installation options of the Sereno
Camera Wall Mount kit.
Mounting on Metal Surfaces
The wall mount base will mount directly to any metallic surfaces such as metal desks,
file cabinets, drawers, etc., and still have enough strength to attach and hold the
Sereno video camera.
1. Choose a mounting location that provides visibility of the subject matter and
attach magnetically.
2. Proceed to Connecting the NMX-VCC-1000 Camera .
Other Surface Mounting
Mount the wall mount kit to a solid surface wall using the included #8 screws and
wall anchors if needed for drywall installations.
Solid Surface Installations
1. Choose a suitable mounting location.
2. Hold the base to the wall and drive the screws through it and into the wall.
3. Proceed to Connecting the NMX-VCC-1000 Camera .
Drywall Installations
1. Use the base as a template to mark two hole locations on the wall. The holes
should be 2.5-inches (63.5 mm) apart center to center as shown in FIG. 2.
2. Remove the base and drill the two marks out to 3/16th diameter to
accommodate the wall anchors.
3. Lightly tap the anchors to drive them into the new holes.
4. Holding the base back up to the wall, insert the #8 screws through the holes in
the base and into the wall anchors. Refer to FIG. 3
5. Tighten the screws into the anchors until snug.
Connecting the NMX-VCC-1000 Camera
The Sereno video camera has a reversible, weighted base for table-top mounting or
wall/inverted mounting. The camera base has a single bottom screw that enables it
to convert from a rubber bottom for table-top surface mounting to a metal bottom
for magnetically mounting to this wall mount kit.
If the camera is new or has been desktop mounted, the rubber base is exposed on
the bottom of the unit. The base needs to be reversed to expose the smooth painted
metal side before mounting the camera to the new wall mount base.
1. Remove the screw in the base plate.
2. Remove and flip the insert over with the shiny black painted side of the base
showing and reinstall using the same screw.
3. Line up the studs of the wall mount base with the holes in the camera metal
plate. See FIG. 5
4. Once close enough, the magnetism will draw the camera down on the posts
creating a strong magnetic bond between them.
5. Tilt the camera head up towards the subject matter.
6. If the camera is mounted upside down, reposition/rotate the camera head so
the image will appear correct on the display (AMX logo should be right side up).
Access this Quick Start Guide online using your mobile device to scan the QR code
located on the bottom of the NMX-VCC-1000 Sereno Video Camera package.
FIG. 1 NMX-VCC-1000 SERENO CAMERA WALL MOUNT KIT
FIG. 2 BASE PLATE MOUNT CENTER TO CENTER
FIG. 3 MAGNETIC MOUNT ADAPTER SHEET ROCK INSTALLATION
Insert screws through
the base and into
Insert anchors into
wall anchors
holes drilled in
drywall
FIG. 4 CAMERA BASE PLATE REVERSAL
FIG. 5 CONNECTING SERENO TO THE MAGNETIC MOUNT ADAPTER
Remove screw to
flip base insert
Wall mount base has
and reinstall
studs that fit into the
metal plate holes
Line up studs with holes in base to secure magnetic adhesion
Produktspecifikationer
| Varumärke: | AMX |
| Kategori: | Inte kategoriserad |
| Modell: | Sereno NMX-VCC-1000-WM |
Behöver du hjälp?
Om du behöver hjälp med AMX Sereno NMX-VCC-1000-WM ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad AMX Manualer
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
2 Januari 2025
27 December 2024
7 December 2024
25 September 2024
25 September 2024
24 September 2024
Inte kategoriserad Manualer
- Morningstar
- Di4
- Air King
- Viomi
- Tuur
- Viscount
- EK Water Blocks
- Fein
- Lazer
- Caroma
- Sagemcom
- Envitec
- Stelzner
- EchoMaster
- Kayoba
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025