Apc ProtectNet PRM4 Bruksanvisning

Apc Inte kategoriserad ProtectNet PRM4

Läs gratis den bruksanvisning för Apc ProtectNet PRM4 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 13 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 7 recensioner. Har du en fråga om Apc ProtectNet PRM4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

ProtectNet® Modular Data Line

Installation Manual

Surge Protection System

Thank you for purchasing APC’s Modular Data Line Surge Protection System. Please fill out the supplied Warranty Registration Card or an on-line Product Warranty Registration form at www.apc.com.

APC’s Modular Data Line Surge Pr variety of interchangeable surgotection System consists of a e suppression modules installed in either a four position “PRM4” or a 24 position “PRM24” chassis with the mounting hardware and ground wire. A list

of the modules that are available, and the types of data lines they protect are provided below. The PRM4 is designed to mount inside a home wiring enclosure. The PRM24 is designed to mount in a standard 19-inch rack enclosure.

This manual provides basic installation information for the PRM4 chassis and associated modules. For PRM24 installation information, reference APC manual 990-1383A.

Note: Procedures provided in this document are not intended to supersede local standards or codes. Reference the Telecommunications Industries Association and Electronic Industries Alliance publication “Commercial Building,

Telecommunications Cabling Standard, General Requirements” (document number TIA/EIA-568-B.1-2001) to ensure the system wiring is installed properly.

Safety

Please read and save these instructions, and observe the following safety precautions.

•Use the system in a protected environment only.

•Never install telephone wiring or coaxial cable during a lightning storm.

•Follow the installation instructions carefully. The current limiting feature of this product could be rendered inoperable if the product is improperly installed.

.apc.com

Completed Assembly

Remove Install

Completed Assembly

Figure 2. Side-by-Side Mounting

Figure 1. Stacked Mounting and Module Installation

Detail A - PRMLB (Optional) Mounting Bracket Orientation

General Installation

Other Considerations

• Do not install this device in an environment where the operating temperature exceeds 0 to 40 oC (32 to 104oF).

• Do not install this device where the relative humidity exceeds 95%, non-condensing.

• Do not store this device in an environment that exceeds 0 to 45oC (32 to 113oF).

Chassis Installation

APC recommends the ProtectNET PRM4 Data Line Surge Protection chassis (X

XX in Figure 1) be installed using the optional mounting brackets (see Detail A, Figure 1) that

are available from APC (order PRMLB). In applications where more than one PRM4 chassis is used, the chassis’ can be stacked (see Figure 1), or mounted side-by-side (see

Figure 2) using the joining plate Y

YY, and the machine screws supplied with the chassis.

Module Installation

The PRM4 chassis is designed to accomodate up to four data line or coaxial cable modules. To install a module, remove the two machine screws Z

ZZ that secure the insert

plate [

[

[[ \

\\ to the "U bracket" bezel holder . Remove one of the blank panels ]

]

]] by pulling it straight out of the chassis. Align the module, either ^

^^ or _

__, with the groove

in the chassis and slide the module fully into the chassis. After installing all the required modules, replace the "U bracket" bezel holder \

\\, and install the insert plate. The U

bracket bezel holder is provided to prevent modules from being accidently removed from the chassis.

Telephone or Coaxial Cable Installation

To install a data line cable `

``, connect the input RJ-45 connector to the signal source, and then connect to the upper data connector on the module. Connect a data line cable

from the module’s lower connector to the equipment to be protected. To accomodate four mNote: odules, the four blank panels in the center of the module must be removed.

To install coaxial cables a

aa, connect one end of the cable to the signal source. Connect the other end of the cable to the upper input connector of the module marked IN.

Connect the output cable "F" connector from the module’s lower connector marked OUT to the device to be protected (CATV, DSS, cable modem, or antenna system).

Grounding

The chassis must be grounded to a proper protective earth ground (see Figure 3). In a typical home/office environment, this can be accomplished by grounding the chassis to

the transient voltage surge supression (TVSS) ground of an uninterruptable power supply (UPS), or to your computer chassis. If the chassis is mounted in a structured wiring

cabinet, ground the chassi chine screw, and threads to earth ground via the cabinet's earth ground connection. A ground wire, ma ed mounting hole are provided to be used

when grounding the chassis.

[

[[

]

]]