Ashdown Engineering HOD-600 Bruksanvisning
Ashdown Engineering
mottagare
HOD-600
Läs gratis den bruksanvisning för Ashdown Engineering HOD-600 (7 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6 recensioner. Har du en fråga om Ashdown Engineering HOD-600 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
INPUT - There is a single instrument input provided linked to
a PASSIVE/ACTIVE selector switch. The Passive input (switch
out) is high sensitivity and also high impedance to suit the
output from PASSIVE basses. The Active input (switch in) is
low sensitivity and lower impedance to suit the output from
ACTIVE basses.
INPUT CONTROL - The INPUT control sets the signal level
through the preamp in conjunction with the INPUT LEVEL VU
Meter. This is adjusted to give a reading of 0VU on the meter
for average playing dynamics with occasional peaks into the
red region. Please note that the setting of this may have to be
re-adjusted after modication of the EQ controls.
PUSH FLAT / SHAPE - With this button in its OUT position a
xed E.Q. is superimposed on the preamp to give a bright but
punchy character to the sound. Pushing this button IN returns
the preamp to a Flat frequency response. This function may
also be controlled from a footswitch. For the footswitch to
operate this button must be in its OUT position.
DOOM - This routes the signal either through a clean Solid
State amplication section (control on zero) or through a
Dual Triode Tube amplication/overdrive section in order
to add either tonal character i.e. warmth with the control
set at 9 o’clock, a slight edge in the sound at 12 0’clock
through to an increasing degree of Tube distortion/over-
drive as the control is advanced to maximum.
A Mix of these two amplication sections can be achieved
with this control.
N.B. The degree of tube distortion provided by this control
will also depend on the setting of the INPUT control.
DOOM IN/OUT - This push button switches the valve drive
section IN or OUT. This function may also be controlled from
the Ashdown 4 way footswitch. For the footswitch to operate
this button must be in its OUT position.
E.Q. IN / OUT - This push button switches the Equalisation
section IN or OUT i.e. the Bass, Middle and Treble controls
plus the two sets of sliders placed between each of these.
WWW.ASHDOWNMUSIC.COM
HEAD OF DOOM USER GUIDE:
Produktspecifikationer
| Varumärke: | Ashdown Engineering |
| Kategori: | mottagare |
| Modell: | HOD-600 |
Behöver du hjälp?
Om du behöver hjälp med Ashdown Engineering HOD-600 ställ en fråga nedan och andra användare kommer att svara dig
mottagare Ashdown Engineering Manualer
8 September 2024
31 Augusti 2024
29 Augusti 2024
28 Augusti 2024
28 Augusti 2024
28 Augusti 2024
27 Augusti 2024
27 Augusti 2024
mottagare Manualer
- DirecTV
- Jamo
- Galaxy Audio
- Camille Bauer
- Edwards Signaling
- Bugera
- Ecler
- Oculus VR
- FiveO
- Bresser
- Mtx Audio
- Arcam
- Trace Elliot
- Intelix
- Unison Research
Nyaste mottagare Manualer
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025