Asrock H81TM-ITX R2.0 Bruksanvisning
Läs nedan 📖 manual på svenska för Asrock H81TM-ITX R2.0 (81 sidor) i kategorin moderkort. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/81
Version 1.1
Published February 2015
Copyright©2015 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
4.1 Introduction 45
4.1.1 UEFI Menu Bar 45
4.1.2 Navigation Keys 46
4.2 Main Screen 47
4.3 OC Tweaker Screen 48
4.4 Advanced Screen 55
4.4.1 CPU Conguration 56
4.4.2 Chipset Conguration 58
4.4.3 Storage Conguration 61
4.4.4 Intel® Smart Connect Technology 62
4.4.5 Super IO Conguration 63
4.4.6 ACPI Conguration 64
4.4.7 USB Conguration 66
4.5 Tools 67
4.6 Hardware Health Event Monitoring Screen 70
4.7 Boot Screen 71
4.8 Security Screen 74
4.9 Exit Screen 75
H81TM-ITX R2.0
5
English
Due to limitation, the actual memory size may be less than 4GB for the reservation for sys-
tem usage under Windows® 32-bit operating systems. Windows® 64-bit operating systems
do not have such limitations. You can use ASRock XFast RAM to utilize the memory that
Windows® cannot use.
6
English
1.3 Motherboard Layout
Intel
H81
PCIE1
MINI_PCIE1
CMOS
Battery
USB4_ 5
1
SATA_POW1
LVDS1
DDR3_B1
DDR3_A1
HD L ED ESET R
PL ED PWR BT N
PANEL1
1
BK T _P WR1
1
PNL _ PWR1
1
USB2 _3
1
1
HDMI_SPDIF1
1
HD_ A UDIO1
AUDIO
CO D EC
LAN
SATA_1
CPU_ FAN1
32Mb
BIOS
DMIC 1
1
CLRCMOS1
1
1
Front
Speaker
Mic In
US 2.B 0
T: USB0
B: USB1
RJ-45
US 3.B 0
T: USB0
B: USB1
DC Jack
DVI1
HDMI1
CIR1
CHA_ N1FA
1
H81TM-ITX
RoHS
1
HT PC 1
BL T _VO L1
1
COM1
1
1
HD_ A UDIO2
LPC1
2
SATA_0
43 5 6 7 8 910
13
15
16
14
17
2021
22
23
24
26
25
USB 3.0
18
12
11
1
USB6
1
MO NI R_ SW IT CH1T O
SPEAKER1
1
19
ATX19V_IN 1
1
H81TM-ITX R2.0
7
English
No. Description
1 Internal Power Header (ATX19V_IN1)
2 USB 2.0 Header (USB6)
3 SATA3 Connector (SATA_1)
4 Chassis Fan Connector (CHA_FAN1)
5 Consumer Infrared Module Header (CIR1)
6 SATA3 Connector (SATA_0)
7 USB 2.0 Header (USB4_5)
8 SATA Power Connector (SATA_POW1)
9 Monitor Switch Header (MONITOR_SWITCH1)
10 System Panel Header (PANEL1)
11 Backlight Power Jumper (BKT_PWR1)
12 Panel Power Jumper (PNL_PWR1)
13 LVDS Connector (LVDS1)
14 2 x 204-pin DDR3 SO-DIMM Slots (DDR3_A1, DDR3_B1)
15 Backlight Control Header (BLT_VOL1)
16 COM Port Header (COM1)
17 USB 2.0 Header (USB2_3)
18 CPU Fan Connector (CPU_FAN1)
19 Front Panel Audio Header (HD_AUDIO1)
20 Digital MIC Header (DMIC1)
21 SPDIF Out Connector (HDMI_SPDIF1)
22 3W Audio AMP Output Wafer Header (SPEAKER1)
23 Analog Surround Audio Header (HD_AUDIO2)
24 Home eater PC Header (HTPC1)
25 Clear CMOS Jumper (CLRCMOS1)
26 LPC Debug Header (LPC1)
8
English
1.4 I/O Panel
No. No.Description Description
1 DC Jack* 5 LAN RJ-45 Port**
2 USB 3.0 Ports (USB3_01) 6 USB 2.0 Ports (USB01)
3 DVI-I Port (DVI1) 7 Microphone (Pink)
4 HDMI Port (HDMI1) 8 Front Speaker (Lime)
* Please use a 19V power adapter for the DC jack. is jack accepts dual barrel plugs with an inner diameter of
5.1 mm and an outer diameter of 7.4 mm, where the inner contact is +19 (±10%) VDC and the shell is (centre
positive).
DELTA DELTA-ADP-150TB-150W/19V
HP HP-TBC-BA52-150W/19V
FSP FSP-FSP150-ABAN1-150W/19V
** ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status StatusDescription Description
Of No Link Of 10Mbps connection
Blinking Data Activity Green 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
8762 5431
12
English
Please save and replace the cover if the processor is removed. e cover must be placed if
you wish to return the motherboard for aer service.
H81TM-ITX R2.0
13
English
2.2 Installing the CPU Fan and Heatsink
1 2
CPU_
FAN
14
English
2.3 Installing Memory Modules (SO-DIMM)
is motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM
slots.
e SO-DIMM only ts in one correct orientation. It will cause permanent damage to
the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at incorrect
orientation.
It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; otherwise,
this motherboard and SO-DIMM may be damaged.
H81TM-ITX R2.0
15
English
1
2
16
English
2.4 Expansion Slots (PCI Express Slots)
ere is 1 PCI Express slot and 1 Half mini-PCI Express slot on this motherboard.
PCIe slot:
PCIE1 (PCIe 2.0 p21-x4 slot) is used for PCI Express p21-x4 lane width cards.
mini-PCIe slot:
MINI_PCIE1 (mini-PCIe slot) is used for WiFi module.
Before installing an expansion card, please make sure that the power supply is switched o
or the power cord is unplugged. Please read the documentation of the expansion card and
make necessary hardware settings for the card before you start the installation.
H81TM-ITX R2.0
17
English
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRCMOS1)
(see p.6, No. 25)
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear
the CMOS right aer you update the BIOS. If you need to clear the CMOS when
you just nish updating the BIOS, you must boot up the system rst, and then shut
it down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.
Backlight Power Jumper
(3-pin BKT_PWR1)
(see p.6, No. 11)
1-2 : +19V
2-3 : +12V
Panel Power Jumper
(3-pin PNL_PWR1)
(see p.6, No. 12)
1-2 : +3V
2-3 : +5V
Clear CMOSDefault
18
English
2.6 Onboard Headers and Connectors
System Panel Header
(9-pin PANEL1)
(see p.6, No. 10)
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
Serial ATA3 Connectors
(SATA_0:
see p.6, No. 3)
(SATA_1:
see p.6, No. 6)
ese two SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
GND
R #ESET
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may congure the way to turn
o your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart the
computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. e LED is on when the
system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e
LED is o when the system is in S4 sleep state or powered o (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. e LED is on when the
hard drive is reading or writing data.
e front panel design may dier by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connect-
ing your chassis front panel module to this header, make sure the wire assignments and the
pin assignments are matched correctly.
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
headers and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.
SATA_1 SATA_0
20
English
Analog Surround
Audio Header
(17-pin HD_AUDIO2)
(see p.6, No. 23)
3W Audio AMP Output
Wafer Header
(4-pin SPEAKER1)
(see p.6, No. 22)
Please connect the chassis
speaker to this header.
SPDIF Out Connector
(2-pin HDMI_SPDIF1)
(see p.6, No. 21)
Please connect the SPDIF
Out connector of a HDMI
VGA card to this header
with a cable.
Chassis Fan Connector
(4-pin CHA_FAN1)
(see p.6, No. 4)
Please connect fan cable
to the fan connector and
match the black wire to
the ground pin.
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.6, No. 18)
is motherboard pro-
vides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL
SPDIFOUT
GND
1
GN D
+ 12V
FAN_SPEED
FA
N_SPEED_CONTROL
1
2
3
4
12
PIN Signal
Name PIN Signal
Name
18 SENSE 17 KEY
16 LFE 15 A_GND
14 A_GND 13 Center
12 Surr_Rear_R 11 A_GND
10 A_GND 9Surr_Rear_L
8Surr_Side_R 7A_GND
6 5A_GND Surr_Side_L
4 3Front_R A_GND
2 1A_GND Front_L
Front_L+
Front_R-
Front_R+
Front_L-
1
H81TM-ITX R2.0
23
English
Monitor Switch Header
(2-pin MONITOR_
SWITCH1)
(see p.6, No. 9)
1
PWRDN
GND
is header can be used to
connect a switch that turns on/
o the LVDS panel display’s
backlight.
24
English
Chapter 3 Software and Utilities Operation
3.1 Installing Drivers
e Support CD that comes with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. e CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu does not appear automatically, locate and double click on the le
“ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
e drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. erefore, the drivers you install can work
properly.
Utilities Menu
e Utilities Menu shows the application soware that the motherboard supports.
Click on a specic item then follow the installation wizard to install it.
To improve Windows 7 compatibility, please download and install the following hot x
provided by Microso.
“KB2720599”: http://support.microso.com/kb/2720599/en-us
26
English
Tools
Various tools and utilities.
XFast RAM
Boost the system’s performance and extend the HDD’s or SDD’s lifespan! Create a
hidden partition, then assign which les should be stored in the RAM drive.
XFast LAN
Boost the speed of your internet connection! Select a specic mode for making the
designated program's priority highest.
Fast Boot
Fast Boot minimizes your computer's boot time. Please note that Ultra Fast mode
is only supported by Windows 8.1/8 and the VBIOS must support UEFI GOP if you
are using an external graphics card.
OMG
Schedule the starting and ending hours of Internet access granted to other users.
Place X marks on the time table to disable the Internet.
Good Night LED
Switch o the Power/HDD LEDs when the system is on, and automatically switch
o the Power and Keyboard LEDs when the system enters into Standby/Hibernation
mode.
H81TM-ITX R2.0
27
English
FAN-Tastic Tuning
Congure up to ve dierent fan speeds using the graph. e fans will automatically
shi to the next speed level when the assigned temperature is met.
Dehumidier
Prevent motherboard damages due to dampness. Enable this function and
congure the period of time until the computer powers on, and the duration of the
dehumidifying process.
USB Key
Plug in the USB Key and let your computer log in to windows automatically!
Disk Health Report
Disk Health Report is a hard disk health monitoring utility that displays detailed
HDD information, such as hard disk model, serial number, rmware, power on
count, power on hours, S.M.A.R.T. values, current temperature, etc. HDD, SSD
and optical disk drives are all supported. e health status block displays Good
(in green color), Caution (in yellow color) or Bad (in red color). Click on the health
status icon to congure settings for an alert to be triggered.
28
English
OC Tweaker
Congurations for overclocking the system.
System Info
View information about the system.
*e System Browser tab may not appear for certain models.
H81TM-ITX R2.0
29
English
Live Update
Check for newer versions of BIOS or drivers.
Tech Service
Contact Tech Service if you have problems with your computer. Please leave your
contact information along with details of the problem.
H81TM-ITX R2.0
31
English
3.3 Intel® Smart Connect Technology
Intel® Smart Connect Technology is a feature that periodically wakes your computer
from Windows® sleep state to refresh email or social networking applications. It
saves your waiting time and keeps the content always up-to-date.
3.3.1 System Requirements
mode, directly changing the SATA mode to AHCI may cause Windows 8/7
to crash while booting. If your system is not in AHCI mode, please follow the
instructions below.
1. Press Win + R simultaneously in Windows 8/7, type "Regedit" into the word
box then click .OK
2. Enter into HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\
msahci in Windows Registry Editor. Double click on the value and Start
change the value from . Click on .3 into 0 OK
ere are certain risks. Please backup any important data before operating to avoid loss.
32
English
3.3.2 Setup Guide
Installing ASRock Smart Connect Utility
Step 1
Install ASRock Smart Connect Utility, which is located in the folder at the following
path of the Support CD: \ .ASRock Utility > Smart Connect
Step 2
Once installed, run ASRock Smart Connect from your desktop or go to Windows
Start -> All Programs -> ASRock Utility.
34
English
Step 6
Double-click the Intel® Smart Connect Technology Manager icon in the
Windows system tray.
Step 7
Drag the slider to congure how oen the system will connect to the network to
download updates. Shorter durations will provide more frequent updates, but may
cause more power consumption.
Using Smart Connect
1. Keep the applications which you wish to connect to the internet and receive
updates while the system is in sleep state running. Foxmail for instance, keep
Foxmail running.
2. Click on Windows Start -> the arrow next to Shut down, and click on .Sleep
3. Windows system will enter sleep state.
H81TM-ITX R2.0
37
English
3.4.2 Apps
When the "Apps" tab is selected, you will see all the available apps on screen for you
to download.
Installing an App
Step 1
Find the app you want to install.
e most recommended app appears on the le side of the screen. e other various
apps are shown on the right. Please scroll up and down to see more apps listed.
You can check the price of the app and whether you have already intalled it or not.
- e red icon displays the price or "Free" if the app is free of charge.
- e green "Installed" icon means the app is installed on your computer.
Step 2
Click on the app icon to see more details about the selected app.
42
English
3.5 Start8
For those Windows 8 users who miss the Start Menu, Start8 is an ideal solution that
brings back the familiar Start Menu along with added customizations for greater
eciency.
3.5.1 Installing Start8
Install Start8, which is located in the folder at the following path of the Support CD:
\ .ASRock Utility > Start8
3.5.2 Conguring Start8
Style
Select between the Windows 7 style and Windows 8 style Start Menu. en select
the theme of the Start Menu and customize the style of the Start icon.
44
English
Control lets you congure what a click on the start button or a press on the
Windows key does.
Desktop
Desktop allows you to disable the hot corners when you are working on the desktop.
It also lets you choose whether or not the system boots directly into desktop mode
and bypass the Metro user interface.
About
Displays information about Start8.
H81TM-ITX R2.0
55
English
4.4 Advanced Screen
In this section, you may set the congurations for the following items:
CPU Conguration, Chipset Conguration, Storage Conguration, Intel® Smart
Connect Technology, Super IO Conguration, ACPI Conguration and USB
Conguration.
Setting wrong values in this section may cause the system to malfunction.
Produktspecifikationer
| Varumärke: | Asrock |
| Kategori: | moderkort |
| Modell: | H81TM-ITX R2.0 |
Behöver du hjälp?
Om du behöver hjälp med Asrock H81TM-ITX R2.0 ställ en fråga nedan och andra användare kommer att svara dig
moderkort Asrock Manualer
25 Mars 2025
3 Mars 2025
3 Mars 2025
3 Mars 2025
3 Mars 2025
2 Januari 2025
28 December 2024
27 Oktober 2024
20 Oktober 2024
17 Oktober 2024
moderkort Manualer
- moderkort Asus
- moderkort Sharkoon
- moderkort Gigabyte
- moderkort Supermicro
- moderkort Evga
- moderkort Intel
- moderkort MSI
- moderkort ECS
- moderkort NZXT
- moderkort Foxconn
- moderkort Advantech
- moderkort Elitegroup
- moderkort EPoX
- moderkort Biostar
Nyaste moderkort Manualer
8 April 2025
8 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
1 April 2025
30 Mars 2025