Audio-Technica ATM650 Bruksanvisning

Audio-Technica mikrofon ATM650

Läs gratis den bruksanvisning för Audio-Technica ATM650 (2 sidor) i kategorin mikrofon. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 8 recensioner. Har du en fråga om Audio-Technica ATM650 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

HYPERCARDIOID DYNAMIC INSTRUMENT MICROPHONE

- Tailored response for musical instrument pickup-guitar cabinets,

snare and other percussion.

- Hypercardioid polar pattern reduces pickup of sounds from the

sides and rear, improving isolation of desired sound source.

- Durable performance for professional applications.

- Special dual-wall oating construction reduces handling noise and

assures consistent performance from mic to mic.

- Hi-ENERGY® neodymium magnet for improved output and transient

response.

- Multi-stage at grille design is engineered to enable easy placement

as close as possible to sound source.

- Corrosion-resistant contacts from gold-plated XLRM-type connector.

- Rugged, all-metal design and construction for years of trouble-free

use.

Output from the microphone’s XLRM-type connector is low imped-

ance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin

1 is ground (shield). Output phase is “Pin 2 hot” - positive acoustic

pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be

wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance (Hi-Z)

mic input, connect a Lo-Z balanced cable to a Hi-Z matching trans-

former (A-T CP8201 or equal) at the equipment input.

When using the ATM650 in settings with a stage monitor speaker,

the speaker should be located 135° off axis (45° off rear of the micro-

phone). This placement, in conjunction with the microphone’s uniform

hypercardioid pickup pattern, will virtually eliminate the possibility of

undesired audio feedback.

Take care to keep foreign particles from entering the windscreen. An

accumulation of iron or steel lings on the diaphragm, and/or foreign

material in the windscreen’s mesh surface, can degrade perfor-

mance.

Note: Remove the rubber sleeve at the base of the microphone han-

dle to use the AT8471 isolation stand clamp (not included) for more

secure, permanent installation.

FORM No. ATGC-L0027-06-E

Machida • Toky o • Japan

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

SPECIFICATIONS

ELEMENT Dynamic

POLAR PATTERN Hypercardioid

FREQUENCY RESPONSE 80-17,000 Hz

OPEN CIRCUIT SENSITIVITY -56 dB (1.5 mV) re 1V at 1 Pa

IMPEDANCE 300 ohms

WEIGHT (less cable and accessories) 279 g

DIMENSIONS 164.2 mm - long,

38.8 mm - diameter

OUTPUT CONNECTOR Integral 3-pin XLRM-type

ACCESSORIES FURNISHED AT8470 Quiet-Flex™ stand clamp for

⅝”-27 threaded stand;

⅝”-27 to ⅜”-16 threaded adapter;

Soft protective pouch

Produktspecifikationer

Varumärke:	Audio-Technica
Kategori:	mikrofon
Modell:	ATM650
Färg på produkten:	Zwart
Snäll:	Automatische melkopschuimer
Kraftkälla:	AC
Kan diskas i diskmaskin:	Nee
Skumningskapacitet:	- ml
Rengöringsväg:	Ja