BlueStar RNB364GV2 Fornuis Bruksanvisning
Läs nedan 📖 manual på svenska för BlueStar RNB364GV2 Fornuis (47 sidor) i kategorin KAMINAR. Denna guide var användbar för 18 personer och betygsatt med 4.6 stjärnor i genomsnitt av 9.5 användare
Sida 1/47
1
USE & CARE MANUAL
Freestanding Ranges
RCS (Open/Sealed)
RNB
Platinum™
Precious Metals
2
BlueStar® Freestanding Range Use & Care Manual
MODELS RCS, RNB, Platinum, Precious Metals
THIS APPLIANCE WAS DESIGNED FOR EASE OF INSTALLATION AND OPERATION. HOWEVER, WE
RECOMMEND THAT YOU READ ALL SECTIONS OF THIS MANUAL BEFORE YOU BEGIN INSTALLATION.
INSTALLATION MUST BE PERFORMED BY AN APPROVED GAS INSTALLER OR GAS SERVICE TECHNICIAN OR
THE WARRANTY IS VOID. IN THE COMMONWEALTH OF MASSACHUSETTS A LICENSED PLUMBER OR GAS
FITTER CAPABLE OF REVIEWING AND PERFORMING THE MANUFACTURER’S INSTALLATION CHECKLIST
SHOULD INSTALL THIS APPLIANCE. THE INSTALLATION CHECKLIST IS INCLUDED AT THE REAR OF THIS
BOOKLET.
DO NOT REMOVE PERMANENTLY AFFIXED LABELS, WARNINGS OR DATA PLATES FROM YOUR APPLIANCE.
THIS MAY VOID THE MANUFACTURER’S WARRANTY AND/OR HINDER EFFECTIVE SERVICING AND
MAINTENANCE.
THESE INSTRUCTIONS ARE TO REMAIN WITH THE APPLIANCE AND THE CONSUMER IS TO RETAIN THEM FOR
FUTURE REFERENCE.
WARNING: If the informaon in this manual is not followed exactly, a
re or explosion may result causing property damage, personal injury
or death.
- Do not store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance
Do not touch or acvate any electrical switch
Do not use any phone in your building
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instrucons.
If you cannot reach your gas supplier, call the re department
- Installaon and service must be performed by a qualied
installer, service agency or the gas supplier.
NOTE: WARRANTY SERVICE MUST BE PERFORMED BY AN AUTHORIZED SERVICE AGENT. YOU MAY
REQUEST WARRANTY SERVICE BY CALLING 800-449-8691. YOU MAY ALSO REQUEST SERVICE VIA THE
INTERNET BY SUBMITTING THE SERVICE REQUEST FORM AT WWW.BLUESTARCOOKING.COM
In the Commonwealth of Massachusetts, gas connections must be performed by a licensed plumber or
licensed gas tter.
WARNING: This product can expose you to chemicals including carbon monoxide which is known to the
state of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
© Copyright 2019 Prizer Painter Stove Works, Inc. All specications are subject to change without prior notication –
3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Read all instructions before using your appliance. Follow these important safety precautions to reduce the risk of re,
electric shock, personal injury or property damage.
Do not remove permanent labels, warnings or data plates including the serial number from your appliance. Removal may
void the manufacturer’s warranty and/or hinder effective servicing and maintenance.
If the information in this manual is not followed exactly, a re or explosion may result causing property
damage, personal injury or death.
Do not store gasoline, aerosol cans, sealed containers any ammable vapors and liquids in the vicinity or
of this or any other appliance.
Do NOT operate the convection fan during the initial pre-heat of the oven or while broiling.
If You Smell Gas
Do not try to light any appliance.
Do not touch or activate any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from outside your home . Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the re department.
Installation must be performed by an approved gas installer or gas service technician or the warranty is
void. In the Commonwealth of Massachusetts a licensed plumber or gas tter capable of reviewing and
performing the manufacturer’s installation should install this appliance.
Tipping Hazard
A child or adult can tip the range over which may cause serious personal injury or death.
Make sure the anti-tip bracket is securely installed.
Ensure the anti-tip bracket is engaged when the range is moved.
Do not operate the range without the anti-tip bracket in place.
4
GENERAL AFETY NSTRUCTIONS S I
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
SAVE THESE INSTRUCTIONS
Your appliance should be installed by a qualied gas installation technician. Have the technician show
you the exact location of the gas shutoff valve on the incoming gas line so you know how to turn off
the gas if necessary.
Never use this appliance as a space heater to warm a room. Doing so may result in carbon monoxide
poisoning and overheating of the oven.
Do not touch the hot surfaces of the range including the burners, burner grates, cooktop, backguard,
oven and oven door interior.
Before any maintenance or repairs are performed, disconnect the appliance from the electric suppl y.
In the event of a power failure, do not attempt to operate the appliance or light any of the burners. This
is a gas red appliance that uses electrical components such as the ignition and safety devices.
Do not attempt to repair or replace any part of this appliance unless specifically instructed to do so in
this manual. In-warranty service must be performed by an authorized service agency.
Only use this appliance for the intended purposes described in this user manual.
This appliance should be operated with a properly sized and operational ventilation hood.
The ventilation and ue ways of this appliance must remain unobstructed at all times.
Additional care should be exercised if your appliance is equipped with a high-shelf. During heavy or
continued use this shelf may become hot. Do not place combustible materials or plastics on this shelf.
Do not sit, stand, or climb on any part of the appliance including the oven door and cooktop. Serious
injury may occur.
Do not store items of interest to children above the appliance.
Never leave the appliance unattended during use. Boil-overs may occur, causing spills which may
ignite.
K FEEP LAMMABLE ATERIALS WAY ROM THE ANGE AND VEN URNERM A F R O B
BlueStar’s Platinum™ Series PowR Oven™ uses open flame technology. Flammable materials inside
the oven when the oven is in use may ignite.
Do not store ammable materials on, in or near the appliance. Keep the appliance area clean and free
of combustible materials, gasoline and other ammable vapors and liquids, aerosol and sealed
containers like baby food jars Check before each use to make sure that no hazardous materials are in .
the area.
Never wear loose fitting clothing or garments with loose sleeves or strings while using this appliance.
Use care when reaching over the range or into the oven.
Do not let cooking grease accumulate in or near the range or inside the oven, since it may ignite.
Clean the grease drip trays and ventilation hood lters frequently to prevent grease build- up.
5
IMPORTANT SAFETY INFORMATION
SAVE THESE INSTRUCTIONS
I T E F , TN HE VENT OF IRE AKE THE OLLOWING TEPS TO REVENT NJURY AND IRE PREADING F S P I F S
Do not use water on grease res. Never pick up a aming pan. Turn off the controls and smother the
aming pan with a fitted lid, cooking sheet or large at tray.
If there is a re in the oven, turn off the oven and keep the oven door closed.
It is recommended you purchase a multi-purpose dry chemical or foam-type re extinguisher for your
home. Store it in close proximity to your appliance.
C S IOOKTOP AFETY NSTRUCTIONS
The push-in and turn control knobs on this appliance are designed to be child-safe, however are not a
guarantee of safe operation.
Do not leave children alone or unattended in the kitchen while the appliance is in use.
When aming liquor or other spirits, and if your appliance is installed under a ventilation hood, TURN
THE FAN OFF. The draft created could cause the ames to spread.
Turn pot and pan handles inward so they do not extend over adjacent burners or the front of the range
to reduce the risk of burns, igniting ammable materials, and spillage.
After use do not touch the range surface until completely cooled.
Never leave the surface burners unattended at medium or high heat settings. Foods, especially oily
foods, may ignite resulting in re that could spread to surrounding cabinets.
Never leave oil unattended while frying. If allowed to heat beyond its smoking point, oil may ignite
resulting in re that may spread to surrounding cabinets. Use a deep fry thermometer whenever
possible to monitor oil temperature and operate with safe limits.
To avoid oil spillover and re, use a minimum amount of oil when shallow pan-frying and avoid
cooking frozen foods with excessive amounts of ice.
Use proper pan size and avoid pans that are unstable or easily tipped. Select cookware that is
matched to the size of the burner. Burner ames should be adjusted so that they do not extend
beyond the bottom of the pan. Excessive ames may be hazardous.
When using glass/ceramic cookware, make sure it is suitable for cooktop service. Some materials
may break because of sudden change in temperature.
Do not use cookie sheets or aluminum foil to cover the grates or line any part of the cooktop. Doing so
may result in carbon monoxide build-up and poisoning, over heating the cooktop surfaces, or a
potential re hazard.
6
O S IVEN AFETY NSTRUCTIONS
Do NOT operate the convection fan during the initial pre-heat of the oven or while broiling.
an OPEN FLAME. Improper use of the oven may result in The Platinum™ Series oven operates with
a FIRE HAZARD. Please review page 28 for more safety instructions.
Do NOT cover the bottom of the oven oor with aluminum foil or any oven liner.
Only use dry potholders. Moist or damp potholders on hot surfaces may result in steam burns. Do not
allow potholders to touch hot burner areas. Do not use a towel or other bulky material as a potholder.
Do NOT heat unopened food containers or jarred products like baby food in the oven. The built-up
pressure may cause the container to explode.
Keep the oven door closed at all times when lighting the oven and broiling. Open only to insert or
remove food.
Do NOT cover an entire oven rack with any material such as aluminum foil. It will block airow
throughout the oven and may cause carbon monoxide poisoning. Aluminum foil linings may trap heat,
creating a re hazard.
Do NOT use a silicone mat the bottom of the oven. This will block airow throughout the oven and on
may cause carbon monoxide poisoning.
Do NOT place any pot, pan or food directly on the oven oor when baking.
Do NOT put your face near the infrared broiler.
Do NOT store food, pots or pans, cooking equipment or containers in the oven when not in use.
Keep the oven free from grease buildup. Grease in the oven may ignite.
7
THANK YOU & WELCOME
Thank you for your purchase and welcome to the BlueStar® Family!
BlueStar® ranges are designed for discerning home chefs who demand restaurant-quality results in their own
kitchens. As the owner of a new BlueStar® range you can look forward to years of culinary excellence. You
will prepare meals with the speed and accuracy of a professional chef right in your own kitchen. All equipment
is designed and manufactured to the highest quality standards in the industry specically to meet the needs of
the world’s most demanding chef: you. From simmering to sautéing, baking and broiling these versatile
ranges provide the exibility you need in any cooking application. Please review and familiarize yourself with
this Use & Care Guide which includes operating and cleaning instructions as well as tips for getting the most
out of your range.
Since 1880, we have been handcrafting the highest quality ranges at our Pennsylvania factory. If your range
ever needs attention, please be sure to use a BlueStar® certied service provider recommended by our sales
service team. Our service team can be reached at 1- - -8691 or serviceteam@bluestarcooking.com. 800 449
Please take a few moments now to ll in the Service Information on PAGE 8 for your future reference. In the
event you require parts or service, this information will be needed to ensure you receive the highest quality
service we can provide.
We hope you enjoy your new range,
The BlueStar® Team
PLEASE NOTE: ALL RANGES SHOULD BE INSPECTED UPON ARRIVAL. PER THE WARRANTY ANY
COSMETIC ISSUES MUST BE REPORTED TO YOUR DEALER WITHIN 7 DAYS OF DELIVERY. THE
PERFROMANCE CHECKLIST MUST BE COMPLETED BY THE CERTIFIED INSTALLER WITHIN 15 DAYS
OF INSTALLATION AND SUBMITTED.
8
SERVICE INFORMATION
Date of Purchase
Model Number
Serial Number
Dealer Name
Dealer Phone
Dealer Address
Date of Installation
Installer Name
Installer Phone
Installer Address
Your installer should complete the Performance Checklist, found in the Installation Manual or page 45
of this manual, before leaving your residence. Mail the completed checklist to: Warranty Department
Prizer-Painter Stove Works Inc. 8 June Avenue, Blandon, PA 19510. 31
NOTE: WARRANTY SERVICE MUST BE PERFORMED BY AN AUTHORIZED SERVICE AGENT. YOU
MAY REQUEST WARRANTY SERVICE BY CALLING 800- -8691. YOU MAY ALSO REQUEST SERVICE 449
VIA THE INTERNET BY SUBMITTING THE SERVICE REQUEST FORM AT
WWW.BLUESTARCOOKING.COM
In the Commonwealth of Massachusetts, gas connections must be performed by a
licensed plumber or licensed gas tter.
9
GETTING STARTED
We know you are excited to start cooking and baking with your new BlueStar® range. Before you begin, it is essential that
you follow these steps for safe and optimal use.
Become familiar with all the parts of your range.
Remove and properly discard all temporary labels and packaging material from the cooktop, burners, burner grates,
oven exterior, oven interior, oven rack glides and oven racks Remove all: cardboard, zip ties paper and plastic . ,
sheathing used as packaging.
Do not remove zip ties beneath burners. These are needed to hold the igniter wires in place. the
Wash all removable parts including ring grates top grates, oven racks, oven rack glides in hot, soapy water. , and
Rinse well and dry thoroughly. See the Care and Cleaning section.
Register your appliance by mailing the Performance Checklist, completed by your installer, and mail to the below
address. The Performance Checklist can be found in the Installation Manual or on page of this manual or online 45 at
www.bluestarcooking.com/support/product-registration/.
Warranty Department
Prizer-Painter Stove Works Inc.
318 June Avenue
Blandon, PA 19510
Perform the Oven Burn-Off procedure before using your oven the first time. The Oven Burn-Off
removes all factory oils and residue.
Season your griddle or French T before rst use op
Do NOT operate the convection fan during the initial pre-heat of the oven or while broiling.
ATTENTION
ATTENTION
10
COOKTOP
BURNERS
B Y B EFORE OU EGIN
Each of your burners has a specific BTU (British Thermal Unit) rating. Before disassembly, note the
location of each burner. If a burner is replaced in the wrong position it may not function correctly.
Become familiar with the location of your burners. Below are the standard burner congurations.
Platinum Series Ranges: 24”, 30”, 36”, 48” and 60”
RNB Series Ranges: 24”, 30”, 36”, 48” and 60”
ATTENTION
11
.
Precious Metals Series Ranges: 30” and 36”
RCS Series Ranges (Open Burner): 30” and 36”
RCS Series Ranges (Sealed Burner): 24”, 30” and 36”
12
B OURNER PERATION
Push in and turn the control knob counter clockwise to HIGH start the ignition process. The igniter will spark and to
make a clicking sound. The clicking will stop after the burner ignites. The initial ignition may take a few seconds. You
may hear multiple clicks before it ignites.
After ignition, turn the knob to your desired setting.
Turn the knob to OFF to extinguish the burner. The ame may linger for several seconds until all the gas in the feeder
tube is burned off.
If the burner does not ignite, see the Before Calling for Service section for possible causes and
solutions.
Burners have a re-ignite feature in case the ame is extinguished for any reason. It may take several
seconds for the burner to re-ignite.
Never operate the burner with the knob set between the HIGH and OFF position. The ame
will NOT re-ignite in this position and a gas leak could occur.
B S URNER ETTINGS
Burners can be set to any setting between LOW/SIMMER and HIGH.
The ame should be adjusted to not wrap around the bottom edge of any pot or pan using the knob.
If the ame is set too high in relation to the edge of the pot or , you might scorch the backguard or pan
other areas around your range
Do not leave empty non-stick pans on the French Top as the heat may damage the coating and the
French Top surface.
At the HIGH setting, flames should appear as a defined cone with a dark blue center and light blue outside. Some
yellow/orange ame may be seen depending on the type of gas and the supply line.
R G T G ING RATES AND OP RATES
OPEN BURNER MODELS TIP: When placing the top grate back on the burner support, locate the sides with the raised
edges and ensure they are positioned to the left/right side of the burner. Insert the ring grate into the top grate by aligning
the small notch in the top grate with the small indents in the ring grate.
If the top grate is unsteady, remove both the top & ring grates, and adjust the four screws in the corners underneath the
top grate accordingly to even out the top grate.
SEALED BURNER MODELS TIP: When placing the top grate back on the cooktop, locate the pin on the bottom of the
grate and place inside the positioning holes of the cooktop.
Simmer Burner (some models)
The SIMMER burner gives you a choice of simmer settings from SIMMER to HIGH. The SIMMER setting can be used to
gently melt chocolate and hold delicate sauces at low temperatures.
For the lowest simmer setting, push in and turn the knob to HIGH to ignite the burner, then turn counter clockwise to
the SIMMER setting on the knob.
o For burners without the SIMMER setting marked on the control knob, push in and turn the control knob to
HIGH to initially ignite the burner, then turn the knob counterclockwise past the LOW indicator until the knob
stops.
For best simmer results only use the simmer burner. To locate the simmer burner on your range, reference the
burner congurations in this manual. The simmer burner is located in the back left position of most ranges.
ATTENTION
CAUTION
ATTENTION
13
Your ring grates, top grates and burner heads may darken over time with use. This is normal.
TIP: To prevent your burners from darkening at an uneven rate, rotate the ring grate and top grates between more and
less active burners.
B URNER CLEANING
Ring Grates and Top Grates
TIP: Clean spills as soon as possible to prevent sticking and build up.
When burner is cool, remove the ring grate, top grate and center filler grate (30” models only).
Wash in hot, soapy water. Rinse well and dry thoroughly to prevent rusting.
Handle gently to prevent nicks/chips, which can lead to rusting
TIP: If you have a nick or chip you can season the area prevent rusting. Nicks or chips are not covered under warranty. to
P corn oil or other high smoke point oil on a paper towel and rub onto rusted area.ut
Wipe away excess oil and replace the part on the range.
Do not submerge the burner grates in water for extended periods of time. Prolonged exposure to moisture
may cause rusting.
For heavy soiling, use a commercially available oven cleaner. Follow the cleaner manufacturer’s
instructions.
Make sure the cleaning chemicals do not contact any stainless steel or painted surface on your
appliance.
Reinstall grates cooktop and make sure they are seated properly, and do not move unsteadily from side in
to side.
Burner Caps (Sealed Burner Models Only)
Burner caps locations are specic to the valves on the front of the unit. If burner caps are removed for
cleaning or other purposes, they must be re-installed in the same location they were removed from.
Failure to do so may result in a burner that will not light or possibly have a high ame.
TIP: Clean spills as soon as possible to prevent sticking and build-up, and to keep the burner ports clear.
For fresh spills, make sure burner is cool and clean with a cloth and hot water.
Burner Heads (Open Burner Models Only)
Burner head locations are specic to the valves on the front of the unit. If burner heads are removed for
cleaning or other purposes, they must be re-installed in the same location they were removed from.
Failure to do so may result in a burner that will not light or possibly have a high ame.
TIP: Clean spills as soon as possible to prevent sticking and build-up, and to keep the burner ports clear.
For fresh spills, make sure burner is cool and clean with a cloth and hot water.
If needed, the burner head can be removed for cleaning:
When cool, remove the ring grate and top grat e.
CAUTION
ATTENTION
ATTENTION
ATTENTION
ATTENTION
14
Lift the burner head up and slide the burner head unit including the venturi tube up and slightly toward the
back of the range so it clears the metal bar.
Disconnect the orange igniter wire from its connector.
Gently clean the exterior of the burner hea with warm, soapy water. DO NOT submerge the burner head d
in water. Rinse well and dry thoroughly.
If the burner ports are clogged, use a push pin, safety pin or other metallic device to carefully clear the
hole. Do NOT use a toothpick or any object that could become stuck in the hole.
Replace the burner head by sliding the burner head unit underneath the metal bar; be sure the air shutter
of the venturi tube slides over and is centered on the gas valve jet.
Reconnect the orange igniter wire to the connector.
Set the burner head in place.
Replace the top grate and ring grate.
If the igniter wire is wet, you will hear clicking and the burner will not ignite. Wait and try again.
It will light after drying.
Burner might ignite but clicking may continue until igniter dries.
WOK OOKINGC
Every burner is wok tted and can be used for wok cooking without a separate wok ring (open burner units only).
TIP: For best results, use your range’s highest BTU rated burner for stir-frying, which are located in the front of the range.
When burner is cool, remove the ring grate from your selected burner.
Position your curved-bottom wok on the open burner cradle of the top grate.
ATTENTION
15
INTEGRATED RIDDLE SOME MODELSG ( )
Before You Begin
You must season your integrated griddle before using. The seasoning process prevents food from sticking and the griddle
from rusting. After seasoning, with time and use, your griddle will darken a develop a rich blue/black color, which is nd
normal.
If you purchased a cast iron griddle separately, do NOT follow the seasoning directions.
Seasoning Your Integrated Griddle
The complete seasoning process takes approximately 90 minutes and requires attention.
Remove and discard all temporary factory labels and packaging, including stainless steel griddle cover.
Wipe off any factory oils and residue with a soft cloth.
Using a dry cotton towel, apply a light coating of high smoke point oil such as corn oil surface. to the griddle’s cooking
Smoke point of the oil must be over 450 . °F
Use a different dry cotton towel and wipe away the excess oil.
Push in and turn the griddle burner control knob counter clockwise to the 300°F setting .
Allow griddle to preheat for 30 minutes. Note: As the griddle heats, it will likely change color to varying shades of
blue/black. This is normal and part of the seasoning process.
Griddle is very hot! Use care with next steps to prevent burns. Do not remove griddle from cooktop.
After 30 minutes at 300°F, use a dry cotton towel and remove the excess oil from the griddle’s surface.
Using a clean, dry cotton towel, apply another coat of corn oil to the griddle’s surface.
Increase the heat setting on the griddle to 325°F. Wait 15 minutes.
Increase the heat setting on the griddle to 350°F. Wait 15 minutes.
Increase the heat setting on the griddle to 375°F. Wait 15 minutes.
Do NOT heat the griddle beyond 375°F during the seasoning process.
Turn the griddle burner knob to OFF. The griddle is still hot.
While the griddle is hot, and with extreme care, use a clean, dry cotton towel to remove excess oil.
Your griddle is now ready for use.
TIP: If food begins sticking to the griddle over time, repeat the seasoning process as needed.
Integrated Griddle Operation
Push in and turn the griddle burner knob counter clockwise to the desired temperature setting.
Allow griddle to pre-heat 20-30 minutes before cooking, for optimal performance.
Turn off griddle when not in use.
Do NOT bang the griddle plate with metal utensils as this will damage the griddle surface.
Avoid gouging the griddle surface.
WARNING
ATTENTION
ATTENTION
ATTENTION
ATTENTION
16
Integrated Griddle Cleaning
Allow griddle to cool to room temperature.
Scrape off excess food with a spatula and wipe off used cooking oil.
For heavy soiling, use a nylon pad coated with a thin layer of cooking oil.
For stubborn stains, you may use a commercially available, FOOD SAFE griddle cleaner. Follow the cleaner
manufacturer’s instructions for use.
After every use, apply a light coating of high smoke point oil like corn oil to the griddle.
Wipe off excess using a clean dry cotton towel.
Never ood a hot griddle plate with cold water. This may cause the griddle grate to crack or warp, and
will void your warranty.
Do NOT use soap directly on griddle surface residue may remain on the surface of the griddle ,
affecting avor of food.
If you choose to remove and wash your griddle plate in hot, soapy water, you must re-season the
griddle using the seasoning process.
To prevent rust, do NOT allow your griddle to stand without a fresh coating of oil.
Check the grease tray after each use to prevent overflowing.
ATTENTION
17
C (HARBROILER SOME MODELS)
Before You Begin
Your charbroiler grate reversible. One side has narrow slats for use with delicate foods like sh and some vegetablesis .
The other side has wider slats for use with larger foods items like steak and chicken. Before igniting the burner, decide
which side is best for the dish you are preparing and place that side face up .
Do not light the charbroiler with food on the grates.
Charbroiler Operation
Etching on front control panel to indicate Griddle knob.
Push in and turn the charbroiler burner control knob counter clockwise to HIGH.
The hot surface igniter will glow and the burner will ignite .
The ignition process may take up to three minutes. You might smell gas before the broiler lights. This is
normal.
After ignition, turn the charbroiler control knob to adjust the flame to the desired height.
Do NOT put your face or hair near the charbroiler.
Charbroiler Cleaning
Allow grates to cool to room temperature.
Remove the porcelain-coated cast iron grates and wash with hot, soapy water and a non-metallic grill brush. Rinse
well and dry thoroughly. Do not submerge grates in water for extended periods as this may cause rusng. If
charbroiler was submerged, do not use until completely dry. Using immediately after being submerged can damage
the surface.
For heavy soiling, use a commercially available oven cleaner. Follow the cleaner manufacturer’s instrucons.
Make sure the cleaning chemicals do not contact any stainless steel or painted surface on your
appliance.
Check the grease tray after each use to prevent overflowing.
ATTENTION
CAUTION
WARNING
CAUTION
19
After every use, apply a light coating of corn oil or high smoke point oil. Wipe off excess using a dry cotton towel.
Never ood a hot French Top ring or surface with cold water. This may cause the French Top’s steel
plates to crack or warp, and will void your warranty.
If you choose to remove and wash your French T rings in hot, soapy water, you must re-season the op
surfaces using the seasoning process.
To prevent rust, do NOT allow your French Top to stand without a fresh coating of oil.
Check the grease tray after each use to prevent overowing.
ATTENTION
20
INTERCHANGEABLE RIDDLE HARBROILER YSTEM LATINUM ERIES ONLYG /C S (P ™S )
The Platinum Series Griddle/Charbroiler system allows for two-zone cooking, with up to 40,000 BTUs of heat. The cast ™
iron, interchangeable, griddle charbroiler system lets you use the griddle or charbroiler anywhere on the range . Visit top
bluestarcooking.com to see the system in action.
The Interchangeable Griddle Charbroiler System comes with 6 pieces.
1. Cast iron frame (skirt) that holds the griddle or charbroiler in place
2. or Cast iron, two-sided griddle (flat ribbed surface)
3. & 4. Pair of cast iron, two-sided (narrow or standard slats) charbroiler grates that are placed side-by-side
5. Stainless steel diffuser (grease diverter), to protect the burners when using the charbroiler
6. Stainless steel cover, for use when the system is kept permanently on the range top
All the pieces of the griddle charbroiler system will be hot during and after use. Use extreme caution while
cooking. Make sure the parts are cool before cleaning.
O PERATION
When cooktop is cool, remove the ring grates and burner grates from any two, adjacent, front- -back burners and the to
set aside. Burners must be removed from front to back, not le to right.
Place the cast iron frame over the two burners, making sure it is seated and level .
If using the griddle, select either the flat or ribbed side and insert the griddle plate into the frame.
If charbroiling, insert the stainless steel diffuser into the frame with the two sides seated in the frame indents.
Select either the narrow or standard slatted side and insert the two broiler grates into the cast iron frame.
Push in and turn each of the two burner control knobs to HIGH, to ignite the burners, and then turn to the desired heat
setting.
TIP For easier clean-up, some water to the grease pan underneath the charbroiler before using–add .
Cleaning
Allow all parts to come to room temperature.
For the cast iron frame, griddle, and charbroiler racks, wash with hot, soapy water and a non-metallic grill brush.
Rinse well and dry thoroughly.
Do not submerge grates in water for extended periods as this may cause rusting.
For the stainless steel diffuser, wash with hot, soapy water. Rinse and dry thoroughly. The stainless steel diffuser is
dishwasher safe.
Platinum Series Griddle Plate Temperature Control
Using the ,000 BTU/25,000 BTU and the 18,000/22,000 BTU burners15
To achieve a 350 degree cooking surface. Turn both burners to the high position for 2 minutes, then turn both burners
to the low position for 7 to 10 minutes. This will create an even 350 degree cooking surface.
To achieve a 400 degree cooking surface. Turn both burners to the high position for 3 1/2 minutes, then turn both
burners to the low position for 7 to 10 minutes. This will create an even 400 degree cooking surface.
WARNING
21
To achieve a 500 degree cooking surface. Turn both burners to the high position for 6 minutes, then turn the 25,000
BTU burner to the low position and the 15,000 BTU burner to the medium position for 7 to 10 minutes. This will
achieve an even 500 degree cooking surface.
Using the Simmer and the 25,000 or 22,000 BTU burners
To achieve a 350 degree cooking surface. Turn both burners to the high position for 3 1/2 minutes, then turn both
burners to the low position for 10 to 12 minutes. This will create an even 350 degree cooking surface.
To achieve a 400 degree cooking surface. Turn both burners to the high position for 5 1/2 minutes, then turn both
burners to the low position for 10 to 12 minutes. This will create an even 400 degree cooking surface.
To achieve a 500 degree cooking surface. Turn both burners to the high position for 8 minutes, then turn the 25,000
BTU burner to the low position and the simmer burner to the medium position for 10 to 12 minutes. This will achieve
an even 500 degree cooking surface.
Platinum Series Charbroiler Temperature Control
Using the ,000 BTU/25,000 BTU and the 18,000/22,000 BTU burners15
To achieve a 350 degree cooking surface. Turn both burners to the high position for 9 minutes, then turn both burners
to the medium position for 7 to 10 minutes. This will create an even 350 degree cooking surface.
To achieve a 400 degree cooking surface. Turn both burners to the high position for 11 minutes, then turn both
burners to the medium position for 9 to 11 minutes. This will create an even 400 degree cooking surface.
To achieve a 500 degree cooking surface. Turn both burners to the high position for 15 minutes, then turn the 22,000
BTU or 25,000 BTU burner to the medium position and keep the 15,000 BTU burner to the high position for 13 to 15
minutes. This will achieve an even 500 degree cooking surface.
Using the Simmer and the 25,000 or 22,000 BTU burners
To achieve a 350 degree cooking surface. Turn both burners to the high position for 12 minutes, then while keeping
the simmer burner on high, turn the 25,000 BTU burner to the medium position for 10 to 12 minutes. This will create
an even 350 degree cooking surface.
To achieve a 400 degree cooking surface. Turn both burners to the high position for 20 minutes. This will create an
even 400 degree cooking surface. This is the maximum temperature you can achieve using the combination of 25,000
or 22,000 BTU and simmer burners.
Produktspecifikationer
| Varumärke: | BlueStar |
| Kategori: | KAMINAR |
| Modell: | RNB364GV2 Fornuis |
Behöver du hjälp?
Om du behöver hjälp med BlueStar RNB364GV2 Fornuis ställ en fråga nedan och andra användare kommer att svara dig
KAMINAR BlueStar Manualer
20 Oktober 2024
24 Juli 2024
KAMINAR Manualer
- KAMINAR Whirlpool
- KAMINAR Parkinson Cowan
- KAMINAR Bertazzoni
- KAMINAR Philco
- KAMINAR Tricity Bendix
- KAMINAR Ariston
- KAMINAR GE
- KAMINAR Lofra
- KAMINAR Matsui
- KAMINAR BEKO
- KAMINAR Zanussi
- KAMINAR Candy
- KAMINAR Pelgrim
- KAMINAR EAS Electric
- KAMINAR Siemens
Nyaste KAMINAR Manualer
21 Oktober 2024
21 Oktober 2024
21 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024