Blustream UEX50B-KIT Bruksanvisning
Blustream
Inte kategoriserad
UEX50B-KIT
Läs gratis den bruksanvisning för Blustream UEX50B-KIT (6 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 9.5 recensioner. Har du en fråga om Blustream UEX50B-KIT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
UEX50B-KIT QUICK REFERENCE GUIDE
Contact: support@blustream.com.au | | support@blustream-us.com support@blustream.co.uk
UEX50B-KIT
Quick Reference Guide
01
Our UEX50B-KIT delivers USB 2.0 extension up to 50m over a single CAT cable
while allowing up to 4 USB devices to be connected to a single USB host. Supports
transmittion data bandwidth up to 480Mbps, backwards compatible with USB 1.1
devices.
Introduction
FEATURES:
• Extends USB up to a distance of 50m over a single CAT cable
• Supports USB 2.0 signal extension
• Backwards compatible with USB 1.1 devices
• Transmitted data bandwidth up to 480Mbps
• 1x USB-B on Receiver for connection to host device
• 4x USB-A hub on Transmitter for conncetion to devices
• USB-A ports 1-2 support 5V1A, USB-A ports 3-4 support 5V500mA
• Simple plug and play, no driver installation or setup required.
*Signal distribution length subject to length of device and host USB cables and CAT cable type
UEX50B-KIT QUICK REFERENCE GUIDE
www.blustream.com.au | www.blustream-us.com www.blustream.co.uk|02
TX Panel Descriptions
1 CAT Cable Connect to CAT cable and to UEX50B-RX Connection -
2 12V/2A DC Power Input screw type connector
3 Power Status Indicator
4 1A USB Device Connection - USB A connection to connect to high current (up to 1A) USB devices
5 500mA USB Device Connection - USB A connection to connect to low current (up to ) USB devices500mA
6 CAT Cable Connect to CAT cable and to UEX50B-TX Connection -
7 Power Switch - Select between powering the Receiver from the Transmitter (TX) or Host PC that USB is connected to
8 USB Host Connection - USB B connection to connect to PC
9 Power Status Indicator
7 8
4
9
RX Panel Descriptions
21
6
53
Device Cabling
It is important that interconnecting CAT cable between the Transmitter and Receiver is terminated using straight the
correct RJ45 pin configuration. The CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable.
Please ensure that the USB cabling used with this product is within specifications for both the distance and maximum
/ expected data rate transfer of the equipment in use. Exceeding distances, or using cabling not suitable for the data
transfer, may stop the UEX50B-KIT from working properly.
It is recommended to keep the USB cabling either side of the UEX50B-KIT to a minimum, using the range of the
equipment to run the distance over the CAT cable infrastructure.
UEX50B-KIT QUICK REFERENCE GUIDE
Contact: support@blustream.com.au | | support@blustream-us.com support@blustream.co.uk 03
Schematic
Produktspecifikationer
| Varumärke: | Blustream |
| Kategori: | Inte kategoriserad |
| Modell: | UEX50B-KIT |
Behöver du hjälp?
Om du behöver hjälp med Blustream UEX50B-KIT ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Blustream Manualer
22 September 2024
17 September 2024
17 September 2024
17 September 2024
Inte kategoriserad Manualer
- Klein Tools
- X-Rite
- Consul
- Starlyf
- Stenda
- Afk
- SunPower
- Leaptel
- Ventus
- V7
- Eureka
- Puls Dimension
- Novus
- Fortinge
- AEA
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025