CDA KC23WH Bruksanvisning
Läs gratis den bruksanvisning för CDA KC23WH (4 sidor) i kategorin Sjunka. Guiden har ansetts hjälpsam av 7 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 4 recensioner. Har du en fråga om CDA KC23WH eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
www.cda.eu
Ceramic Sinks
Installation
2
Installation
Before Installation
Oer up the sink to the worktop and/or the cabinets to confirm that
the external dimensions of the bowl are compatible with the cabinets
themselves.
Confirm that with the sink in position:
• There is adequate space to install any taps or other required
accessories.
• There is adequate space to install the waste pipework and that any
necessary modification to internal shelves to accommodate the waste
(and trap) is acceptable.
• Access to any water stop-cock or other services will still be adequate
after the installation.
Cutting the tap hole
Only cut/punch the tap hole from the top face of the sink.
• Select the tap hole position based on whether left hand or right hand
drainer is required.
• Locate the centre of the required tap hole by transferring
measurements from the cast in features on the underside. Cover the
top of the tap hole cut-out area with masking tape.
• Caution: Ensure that the sink is supported under the hole to be cut
out.
• Using a centre punch and hammer, make an initial cut in the glaze at
the centre of the required hole.
• Still using the punch and hammer enlarge the cut to the full hole size
required for the tap by carefully chipping away.
3
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
Installation
• Refer to the cut-out sizes on the back of this manual and use them
to mark out where the worktop needs to be cut. Double-check the
dimensions before cutting the worktop aperture.
• After cutting out the worktop aperture, we recommend you seal the
cut edges with silicone (or similar) sealant to help prevent ingress of
water.
• It is often easier to mount the taps, waste-fitting and overflow onto the
sink prior to fitting the sink to the worktop.
• Position the sink on the worktop, bedding it into a bed of silicone
sealant.
• After positioning the sink, leave it untouched for 24 hours to allow
the sealant to cure before any water is run into it.
• The taps, waste-fitting and overflow can now be mounted onto the
sink (if not already done) and fully connected to their respective
services.
• To check the waste for leaks, close the plug/basket of the waste
fitting, open the tap and fill the sink to the level of the overflow; turn
o the tap and wait several minutes to verify that the water doesn’t
drain away.
• Empty the sink.
After fitting, ensure that the enclosed “Ceramic Sinks Use and
Maintenance” guide is retained for the customer and/or user of the
sink.
Produktspecifikationer
| Varumärke: | CDA |
| Kategori: | Sjunka |
| Modell: | KC23WH |
Behöver du hjälp?
Om du behöver hjälp med CDA KC23WH ställ en fråga nedan och andra användare kommer att svara dig
Sjunka CDA Manualer
8 September 2024
8 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
3 September 2024
3 September 2024
3 September 2024
3 September 2024
Sjunka Manualer
- Seima
- Franke
- Rangemaster
- Kohler
- Leisure
- Blanco
- Oliveri
- Physa
- Kernau
- Bartscher
- Blaupunkt
- Shaws
- Hotpoint-Ariston
- Fulgor Milano
- Caple
Nyaste Sjunka Manualer
9 April 2025
8 April 2025
8 April 2025
2 April 2025
31 Mars 2025
30 Mars 2025
26 Mars 2025
4 Mars 2025
3 Mars 2025
28 Januari 2025