Chauvin Arnoux CA 10141E Bruksanvisning

Chauvin Arnoux Mätutrustning CA 10141E

Läs gratis den bruksanvisning för Chauvin Arnoux CA 10141E (38 sidor) i kategorin Mätutrustning. Guiden har ansetts hjälpsam av 14 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 7.5 recensioner. Har du en fråga om Chauvin Arnoux CA 10141E eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/38

Conductivity meter

EN - User’s manual

CA 10141E

Information or useful tip.

Battery.

The product is declared recyclable following an analysis of the life cycle in accordance with standard ISO 14040.

Chauvin Arnoux has adopted an Eco-Design approach in order to design this appliance. Analysis of the complete life-

cycle has enabled us to control and optimize the e󰀨ects of the product on the environment. In particular this appliance

exceeds regulation requirements with respect to recycling and reuse.

The CE marking indicates compliance with the European Low Voltage Directive (2014/35/EU), Electromagnetic

Compatibility Directive (2014/30/EU), and Restriction of Hazardous Substances Directive (RoHS, 2011/65/EU and

2015/863/EU)..

The rubbish bin with a line through it indicates that, in the European Union, the product must undergo selective disposal

in compliance with Directive WEEE 2012/19/EU. This equipment must not be treated as household waste.

PRECAUTIONS FOR USE

This instrument is compliant with safety standard IEC/EN 61010-2-030 or BS EN 61010-2-030, for voltages 5V with report to

ground. Failure to observe the safety instructions may result in electric shock, re, explosion, and destruction of the instrument

and of the installations.

■ The operator and/or the responsible authority must carefully read and clearly understand the various precautions to be taken in

use. Sound knowledge and a keen awareness of electrical hazards are essential when using this instrument.

■ Observe the conditions of use, namely the temperature, the relative humidity, the altitude, the degree of pollution, and the place

of use.

■ Do not use the instrument if it seems to be damaged, incomplete, or poorly close.

■ Before each use, check the condition of the housing. Any item of which the insulation is deteriorated (even partially) must be set

aside for repair or scrapping.

■ All troubleshooting and metrological checks must be done by competent, accredited personnel.

Thank you for purchasing this CA 10141E conductivity meter.

For best results with your instrument:

■ read these operating instructions carefully,

■ comply with the precautions for use.

CONTENTS

1. FIRST USE ............................................................................................................................................................................... 4

1.1. Delivery condition ........................................................................................................................................................... 4

1.2. Accessories .................................................................................................................................................................... 4

1.3. Replacement parts ......................................................................................................................................................... 4

1.4. Inserting the batteries ..................................................................................................................................................... 5

2. PRESENTATION OF THE INSTRUMENT ............................................................................................................................. 6

2.1. CA 10141E ..................................................................................................................................................................... 6

2.2. Terminal strip .................................................................................................................................................................. 6

2.3. Functions of the instrument ............................................................................................................................................ 7

2.4. Keypad ........................................................................................................................................................................... 7

2.5. Display ............................................................................................................................................................................ 8

2.6. Setting the time ............................................................................................................................................................... 9

2.7. Prop ................................................................................................................................................................................ 9

3. USE IN STAND-ALONE MODE ........................................................................................................................................... 10

3.1. Calibration .................................................................................................................................................................... 10

3.2. Conductivity measurement .......................................................................................................................................... 16

3.3. Resistivity measurement .............................................................................................................................................. 17

3.4. TDS measurement ....................................................................................................................................................... 18

3.5. Salinity measurement ................................................................................................................................................... 18

3.6. Recording the measurements ...................................................................................................................................... 19

3.7. Analogue outputs .......................................................................................................................................................... 19

3.8. Errors ............................................................................................................................................................................ 21

4. USE IN RECORDING MODE ............................................................................................................................................... 22

4.1. Connection ................................................................................................................................................................... 22

4.2. Get Data Logger Transfer software .............................................................................................................................. 22

4.3. USB link ........................................................................................................................................................................ 22

4.4. Data Logger Transfer software ..................................................................................................................................... 24

4.5. Other software .............................................................................................................................................................. 26

5. TECHNICAL SPECIFICATIONS .......................................................................................................................................... 27

5.1. Reference conditions .................................................................................................................................................... 27

5.2. Electrical specications ................................................................................................................................................ 27

5.3. Memory ......................................................................................................................................................................... 29

5.4. USB .............................................................................................................................................................................. 29

5.5. Power supply ................................................................................................................................................................ 29

5.6. Environmental conditions ............................................................................................................................................. 30

5.7. Mechanical characteristics ........................................................................................................................................... 31

5.8. Compliance with international standards ...................................................................................................................... 31

5.9. Electromagnetic compatibility (CEM) ............................................................................................................................ 31

6. MAINTENANCE ..................................................................................................................................................................... 32

6.1. Cleaning ....................................................................................................................................................................... 32

6.2. Replacement of batteries .............................................................................................................................................. 32

6.3. Serial number ............................................................................................................................................................... 32

6.4. Calibration log ............................................................................................................................................................... 33

6.5. Embedded software version ......................................................................................................................................... 33

6.6. Updating the embedded software ................................................................................................................................. 33

7. WARRANTY ........................................................................................................................................................................... 35

8. APPENDIX 1: NONLINEAR TEMPERATURE CORRECTION OF THE CONDUCTIVITY .............................................. 36

9. APPENDIX 2: SALINITY CALCULATION ............................................................................................................................ 37

Produktspecifikationer

Varumärke:	Chauvin Arnoux
Kategori:	Mätutrustning
Modell:	CA 10141E
Färg på produkten:	Zwart
Vikt:	1320 g
Bredd:	148 mm
Djup:	215 mm
Höjd:	86 mm
Förpackningens vikt:	1460 g
Förpackningens bredd:	250 mm
Djuppackning:	120 mm
Förpackningshöjd:	180 mm
Snäll:	Moederkaart
Användarmanual:	Ja
LED-indikatorer:	Ja
Medföljande kablar:	SATA
Material:	Steel, Aluminium, Plastic
Antal per paket:	1 stuk(s)
Antal fans:	1 ventilator(en)
Para:	3.5 "
HDD-gränssnitt:	SATA III, Serial Attached SCSI (SAS)
Antal skruvar:	8
HDD storlek:	3.5 "
Maximalt antal hårddiskar per hölje:	3
(Ytter) huvudpaketets höjd:	280 mm
(Ytter) huvudförpackningens bredd:	380 mm
(Ytter) huvudförpackningens bruttovikt:	13900 g
(Ytre) huvudpaketets längd:	520 mm
Kvantitet per (yttre) huvudkartong:	8 stuk(s)
Överföringshastighet:	12 Gbit/s
Nyckelfack:	Ja
Hot-swap:	Ja
Ventilator diameter:	60 mm
Antal SATA-anslutningar:	3
Antal-nycklar-ingår:	2 stuk(s)
Antal externa SATA-portar:	2