Chief RPMA024 Bruksanvisning
Sidor 1 Engels Platt panelstöd
Läs bruksanvisningen för Chief RPMA024 gratis online eller ladda ner PDF:en. 22 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
INSTALLATION INSTRUCTIONS
© 2006 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000021
06/06
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1.Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2.Turn projector upside down.
3.Place the four 1/2" spacers on the bottom of the projector over the four threaded mounting inserts.
4.Place the interface bracket onto the four spacers on the bottom of the projector, lining up the four threaded inserts in the bottom of the
projector with the four mounting holes in the bracket.
5.Using the four M4 x 20mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at this
time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with
the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no
representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
SLB-024 and SLM-024 Interface Brackets
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the
specific installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by
calling 1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY
AND DAMAGE TO EQUIPMENT!DO NOT substitute hardware. Use only hardware supplied by manufacturer!
(1) Interface Bracket(4) Screw, Philips Pan Head, Machine, M4 x 20mm ****
(4) 10-24 Thumb Nuts **(4) Washer, Flat, M4
(1) All-Points Security Kit(4) 1/2" x .194" x 1/2" Round Spacer ****
**Only used when installing SLB Interface brackets.
****Used when mounting surface of projector is recessed.
Produktspecifikationer
| Varumärke: | Chief |
| Kategori: | Platt panelstöd |
| Modell: | RPMA024 |
Behöver du hjälp?
Om du behöver hjälp med Chief RPMA024 ställ en fråga nedan och andra användare kommer att svara dig
Platt panelstöd Chief Manualer
Chief RSMAUS Bruksanvisning Chief FCA3X1U Bruksanvisning Chief RPMA302 Bruksanvisning Chief RPA279 Bruksanvisning Chief KSA1018B Bruksanvisning Chief MSS6225S Bruksanvisning Chief TIL1X5AP Bruksanvisning Chief KONTOUR K2C200S Bruksanvisning
Alla Chief Platt panelstöd manualer
Populära i Platt panelstöd
Platt panelstöd Manualer
Nyaste Platt panelstöd Manualer
StarTech.com H2M1AS2-MONITOR-ARM Bruksanvisning Sven С71-11 Bruksanvisning Alogic Glide C32GMA1 Bruksanvisning Kogan KATVULT80LB Bruksanvisning Peerless-AV WMJ022 Bruksanvisning Rocstor ErgoReach ED7 Bruksanvisning XTRARM XTR-FS5030 Bruksanvisning Twelve South HiRise Pro Bruksanvisning Akai 1342TS1 Bruksanvisning Atdec AWMS-HXB-H Bruksanvisning