Cisco Aironet 2600e Bruksanvisning

Cisco Åtkomstpunkt Aironet 2600e

Läs gratis den bruksanvisning för Cisco Aironet 2600e (40 sidor) i kategorin Åtkomstpunkt. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 13 recensioner. Har du en fråga om Cisco Aironet 2600e eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/40

GETTING STARTED GUIDE

Cisco Aironet 2600 Series Access Points

July, 2012

P/N: 78-20842-01

1 About this Guide

2 Introduction to the Access Point

3 Safety Instructions

4 Unpacking

5 Configurations

6 Access Point Ports and Connectors

7 Configuring the Access Point

8 Mounting the Access Point

9 Deploying the Access Point on the Wireless Network

10 Troubleshooting

11 Declarations of Conformity and Regulatory Information

12 Configuring DHCP Option 43 and DHCP Option 60

13 Access Point Specifications

1 About this Guide

This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series

Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this

document.

2 Introduction to the Access Point

The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream

rates over a deployable distance with high reliability when serving clients. The 2600 series provides

high reliability and overall wireless performance.

The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna

options. The access points support full inter-operability with leading 802.11n clients, and support a

mixed deployment with other access points and controllers.

The 2600 series access point is available in both controller-based (Unified) and standalone

(Autonomous) configurations and supports:

• Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios

• Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)

• External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)

Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory

Domains” section on page 6 for a list of supported regulatory domains.

The features of the 2600 series are:

• Processing sub-systems (including CPUs and memory) and radio hardware which supports:

–

Network management

–

CleanAir—Automatic detection, classification, location and mitigation of RF interference

(not available on autonomous or standalone models)

–

ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients

–

VideoStream

–

Location

–

WIDS/WIPS

–

Security

–

Radio Resource Management (RRM)

–

Rogue detection

–

Management Frame Protection (MFP)

–

Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps

data-rates

• 32 MB flash size

• 802.11af/at

–

CDP (Cisco Discovery Protocol)

• 2.4 GHz and 5 GHz 802.11n radios with the following features:

–

3TX x 4RX

–

3-spatial streams, 450 Mbps PHY rate

–

Spectrum intelligence

–

DPD (Digital Pre-Distortion) technology

–

Cisco Vector Beamforming—Implicit Co-phase beamforming for .11ag clients and 1

spatial-stream and 2 spatial-stream clients

–

Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Produktspecifikationer

Varumärke:	Cisco
Kategori:	Åtkomstpunkt
Modell:	Aironet 2600e
Vikt:	1040 g
Bredd:	221 mm
Djup:	221 mm
Höjd:	54 mm
LED-indikatorer:	Status
Frekvensband:	2.4, 5 GHz
Internminne:	256 MB
Antal användare:	- användare (er)
Flashminne:	32 MB
Maximal dataöverföringshastighet:	450 Mbit/s
2,4 GHz:	Ja
5 GHz:	Ja
Antennfunktioner:	Integrated antenna, Detachable antenna
Antal kanaler:	2 kanaler
WAN-port:	Ethernet (RJ-45)
Produktens färg:	Vit
Datahastighet för Ethernet-LAN:	10,100,1000 Mbit/s
Strömförsörjning via Ethernet (PoE) stöd:	Ja
Antal LAN (RJ-45) anslutningar:	1
Temperatur vid drift:	0 - 40 ° C
Temperaturintervall (förvaring):	-30 - 70 ° C
Intervall för relativ operativ luftfuktighet:	10 - 90 %
AC-inspänning:	100 - 240 V
Kryptering/säkerhet:	AES, EAP, EAP-FAST, EAP-TLS, EAP-TTLS, MSCHAPv2, PEAP, TKIP, WPA, WPA2
Växelström Frekvens:	50 - 60 hz
Webbaserad adminstraion:	Nej
Antenner mängd:	4
Antenn ökningsnivå (max):	6 dBi
Kommunikationsstandarder:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11h, IEEE 802.11n, IEEE 802.3af
Intern:	Nej
Stödda protokoll:	FCC, RSS, EN, EMI, ICES, VCCI
Altitud vid drift:	0 - 3000 m
Höjd över havet i avstängt läge:	0 - 4572 m