Columbus P-1 Mark II Bruksanvisning


Läs gratis den bruksanvisning för Columbus P-1 Mark II (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 11 recensioner. Har du en fråga om Columbus P-1 Mark II eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/4
Power on: Green, always on
Sleeping: Green, flashing
Low battery: Red, flashing
Charging: Red, always on
Fully charged: Green, always on
Spy mode: Blue
Parts Description
Main Status Lamp
MicroUSB connector
MicroSD slot
Reset
Log Lamp
GNSS Status Lamp Motion Detection Lamp
1
Acquiring satellite: Always on
GNSS is fixed: Green, flashing
GNSS is fixed (Best Positioning):
Blue, flashing
Motion Detection Mode On/Off:
Always On/Off
Device is in motion: Flashing
Logging a track
Long press the "Power button" to
power on.
Long press the "Power button" to
turn the device off and save the
track.
Do not remove the memory
card while it is turned on,
which will result in data loss!
5
Power button Point of interest button
2
On
Reset
Function button
If the memory card fails to log, the Log lamp will flash continuously
with continuous warning sound. In such case, please format or replace
the card.
Long press: Turn On/Off .
Short press: Turn On/Off Motion
Detecting Mode.
Short press: Mark the current
position as a point of interest (POI).
(for CSV files only)
Long press: Start a new track.
If the device stops responding, use a
pin to press the reset hole to reset.
Short press: Pause / continue
logging (default).
This button can be configured to
other functions, see page 6.
Short press the "Power button" to
turn On/Off the Motion Detection
Mode.
Wait for GNSS positioning in the
open air. The cold start needs 1-3
minutes. When the "GNSS status
lamp" and the "Log lamp" start
flashing, it indicates track logging
has started.
Off
The notch
is on the left.
P-1 M2 supports high capacity SDXC MicroSD card, we recommend the 4G-32G.
Insert the MicroSD card into the slot. Please note the direction of the card. The
notch of the card should be leftward.
CAUTION
GB
This manual is intended to guide you through the safe and
correct use of the product and its accessories, avoiding improper
operations that may result in injury of yourself or any other
person or cause device damage.
The protection class is IP66, P-1 M2 can work normally in rain,
snow and high dust environments. The rubber connector cover
must be fully covered.
Do not immerse P-1 M2 in water. Do not try to damage or
puncture the device, otherwise, electrolyte in its built-in battery
may leak or combust, causing injury or environmental pollution.
As a precision electronics, the product contains no component
that can be repaired by your own. Any attempt to disassemble
the product will void the original manufacturer's warranty.
Thank you for choosing our product.
Point of interest button
Log lamp
Main status lamp
GNSS status lamp
Motion detection lamp
Function button
Power button
Hand strap hole
Rubber connector cover
Quick
Quick
Quick
Quick Quick Star
Star
Star
StarStart
t
t
tt
Quick
Quick
Quick
Quick Quick Star
Star
Star
StarStart
t
t
tt
Pr
Pr
Pr
PrPro
o
o
oofe
fe
fe
fefes
s
s
sss
s
s
ssi
i
i
iion
on
on
onona
a
a
aal G
l G
l G
l Gl GNS
NS
NS
NSNSS D
S D
S D
S DS Da
a
a
aat
t
t
tta Lo
a Lo
a Lo
a Loa Log
g
g
ggge
ge
ge
geger
r
r
rr
Pr
Pr
Pr
PrPro
o
o
oofe
fe
fe
fefes
s
s
sss
s
s
ssi
i
i
iion
on
on
onona
a
a
aal G
l G
l G
l Gl GNS
NS
NS
NSNSS D
S D
S D
S DS Da
a
a
aat
t
t
tta Lo
a Lo
a Lo
a Loa Log
g
g
ggge
ge
ge
geger
r
r
rr
High speed log: Flash every 1 second
(10Hz/5Hz)
Normal log: Flash every 3 seconds
(1Hz/distance interval)
MicroSD card error or no card:
Continuous flashing
Pause: Always on


Produktspecifikationer

Varumärke: Columbus
Kategori: Inte kategoriserad
Modell: P-1 Mark II

Behöver du hjälp?

Om du behöver hjälp med Columbus P-1 Mark II ställ en fråga nedan och andra användare kommer att svara dig