Columbus P-10 Pro Bruksanvisning


Läs gratis den bruksanvisning för Columbus P-10 Pro (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 19 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 10 recensioner. Har du en fråga om Columbus P-10 Pro eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/4
Power on: Green, always on
Sleeping: Green, flashing
Low battery: Red, flashing
Charging: Red, always on
Fully charged: Green, always on
Spy mode: Blue
Parts Description
Main Status Lamp
MicroUSB connectorMicroSD slot
Reset
Log Lamp
GNSS Status Lamp Motion Detection Lamp
1
Track logging: Flash every 3 seconds
Pause: Always on
MicroSD card error or no card:
Continuous flashing
Acquiring satellite: Always on
GNSS is fixed: Green, flashing
GNSS is fixed (Best Positioning):
Blue, flashing
Motion Detection Mode On/Off:
Always On/Off
Device is in motion: Flashing
Logging a track
Long press the "Power button" to
power on.
Long press the "Power button" to
turn the device off and save the
track.
Do not remove the memory
card while it is turned on,
which will result in data loss!
5
Power button Point of interest button
2
On
Reset
Function button
If the memory card fails to log, the Log lamp will flash continuously
with continuous warning sound. In such case, please format or replace
the card.
Long press:Turn On/Off .
Short press: Turn On/Off Motion
Detecting Mode.
Short press: Mark the current
position as a point of interest (POI).
(for CSV files only)
Long press: Start a new track.
If the device stops responding, use a
pin to press the reset hole to reset.
Short press: Pause / continue
logging (default).
This button can be configured to
other functions, see page 5.
Short press the "Power button" to
turn On/Off the Motion Detection
Mode.
Wait for GNSS positioning in the
open air. The cold start needs 1-3
minutes.When the "GNSS status
lamp" and the "Log lamp" start
flashing, it indicates track logging
has started.
Off
The notch
is on the left.
P-10 Pro supports high capacity SDXC MicroSD card, we recommend the 4G-32G.
Insert the MicroSD card into the slot. Please note the direction of the card.The
notch of the card should be leftward.
CAUTION
GB
Thank you for choosing our product.
This manual is intended to guide you through the safe and
correct use of the product and its accessories, avoiding improper
operations that may result in injury of yourself or any other
person or cause device damage.
As a precision electronics, the product contains no component
that can be repaired by your own. Any attempt to disassemble
the product will void the original manufacturer's warranty.
The protection class is IP66, P-10 Pro can work normally in rain,
snow and high dust environments. The rubber connector cover
must be fully covered.
Do not immerse P-10 Pro in water. Do not try to damage or
puncture the device, otherwise, electrolyte in its built-in battery
may leak or combust, causing injury or environmental pollution.
Quick
Quick
Quick
QuickQuick Star
Star
Star
StarStart
t
t
tt
Quick
Quick
Quick
QuickQuick Star
Star
Star
StarStart
t
t
tt
Prof
Prof
Prof
ProfProfessional
essional
essional
essionalessional HD GNSS
HD GNSS
HD GNSS
HD GNSS HD GNSS Data L
Data L
Data L
Data L Data Logger
ogger
ogger
oggerogger
Quick
Quick
Quick
QuickQuick Star
Star
Star
StarStart
t
t
tt
Prof
Prof
Prof
ProfProfessional
essional
essional
essionalessional HD GNSS
HD GNSS
HD GNSS
HD GNSS HD GNSS Data L
Data L
Data L
Data L Data Logger
ogger
ogger
oggerogger
Point of interest button
Log lamp
Main status lamp
GNSS status lamp
Motion detection lamp
Function button
Power button
Hand strap hole
Rubber connector cover


Produktspecifikationer

Varumärke: Columbus
Kategori: Inte kategoriserad
Modell: P-10 Pro

Behöver du hjälp?

Om du behöver hjälp med Columbus P-10 Pro ställ en fråga nedan och andra användare kommer att svara dig