Conair GlideLite GI500 Bruksanvisning
Läs gratis den bruksanvisning för Conair GlideLite GI500 (2 sidor) i kategorin Järn. Guiden har ansetts hjälpsam av 26 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 13.5 recensioner. Har du en fråga om Conair GlideLite GI500 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
                        Sida 1/2
                    
                    
                    
13.  Do not place the soleplate directly on any 
surface or on the appliance power cord 
while the iron is hot or plugged in.
14.  The plug must be removed from the 
electrical outlet before the water reservoir is 
filled with water.
15.  Do not operate steam function without 
properly filling the water tank with water.
16.  The iron should always be turned off 
before plugging in or unplugging from 
an outlet. Never yank cord to disconnect 
from outlet; instead, grasp plug and pull to 
disconnect.
17.  Burns could occur from touching hot metal 
parts, hot water, or steam. Use caution 
when turning a steam iron upside down to 
empty water, as there may be hot water in 
the reservoir.
18.  If you need to clean the iron, unplug and 
allow to cool. Use a slightly damp cloth and 
wipe down the outside of the iron. DO NOT 
use cleaning agents or place the iron in 
water or cleaning fluids. 
19. Do not hold hand in front of steam.
20.  To reduce likelihood of circuit overload, 
do not operate another high-wattage 
appliance on the same circuit.
21.  Never steam or iron clothes that are  
being worn. 
22.  When emitting steam, this appliance may 
cause burns if it is used too close to the 
skin or eyes or if it is used incorrectly. 
To reduce the risk of contact with hot 
water emitting from the steam vents, test 
appliance before use by holding it away 
from the body.
IMPORTANT SAFETY 
INSTRUCTIONS
When using your iron, especially when children 
are present, basic precautions should always be 
taken, including the following:
READ ALL  
INSTRUCTIONS  
BEFORE USING
DANGER – Any appliance is electrically 
live even when the switch is off.
To reduce the risk of death by electric shock:
1.  Always unplug appliance immediately 
after use and before cleaning.
2.  Do not place or store appliance where it can 
fall or be pulled into a tub or sink.
3.  Do not place in or drop into water or other 
liquids.
4.  Do not reach for an appliance that has fallen 
into water. Unplug immediately.
5. Use only in a dry area.
WARNING – To reduce the risk of 
burns, electrocution, fire, or injury to persons:
1.  Children should be supervised to ensure 
that they do not play with the appliance.
2.  This appliance is not intended for use 
by persons (including children) with 
reduced physical, sensory or mental 
capabilities, or lack of experience and 
knowledge, unless they have been given 
supervision or instruction concerning 
use of the appliance by a person 
responsible for their safety.
3.  The iron must not be left unattended while it 
is connected to an electrical outlet.
4.  Use this appliance only for its intended use 
as described in this manual. Do not use 
attachments not recommended by Conair.
5.  The iron must be used and rested on a 
stable surface.
6.  If the supply cord is damaged, it must be 
replaced by the manufacturer, its service 
agent or similarly qualified persons in 
order to avoid a hazard.
7.  Do not allow cord to touch heated surfaces. 
Do not pull or twist cord. Let appliance cool 
completely before emptying or putting away. 
Wrap the cord loosely around the iron when 
storing.
8.  This appliance has a polarized plug (one 
blade is wider than the other). As a safety 
feature, this plug will fit in a polarized outlet 
only one way. If the plug does not fit fully 
in the outlet, reverse the plug. If it still does 
not fit, contact a qualified electrician. Do not 
attempt to defeat this safety feature.
9.  Never drop or insert any object into any 
opening.
10.  Do not use outdoors or operate where 
aerosol (spray) products are being used or 
where oxygen is being administered.
11.  We recommend you do not use an 
extension cord to operate this appliance. If 
an extension cord is absolutely necessary, 
a 15 ampere-rated cord should be used. 
Cords rated for less amperage may 
overheat. Care should be taken to arrange 
the cord so that it cannot be pulled or 
tripped over.
12.  Surfaces of this appliance are hot when in 
use. Do not let heated surfaces touch eyes 
or skin.
23.  When placing the iron on its base, ensure 
that the surface on which the base is 
placed is stable.
24.  The iron is not to be used if it has been 
dropped, if there are visible signs of 
damage or if it is leaking.
25.  Always disconnect the iron from the 
electrical outlet before filling the reservoir 
with water, emptying the water from the 
reservoir, and when the iron is not in use.
26.  Close supervision is required for any 
appliance used by or near children. Do not 
leave the iron unattended while the iron is 
connected or on an ironing board.
SAVE THESE 
INSTRUCTIONS
IMPORTANT 
FOR HOUSEHOLD USE ONLY
DO NOT let children use the appliance.
DO NOT let untrained persons use the 
appliance without supervision. 
NEVER immerse the iron, cable or plug in any 
liquids.
DO NOT leave the hot iron touching fabrics or 
inflammable surfaces.
DO NOT leave the appliance unnecessarily 
plugged in. Disconnect the plug from the outlet 
when the appliance is not being used.
NEVER touch the appliance with wet or damp 
hands.
DO NOT use the power cord or the appliance in 
order to pull the plug out of the outlet.
DO NOT leave the appliance exposed to the 
weather (rain, sun, etc.).
DO NOT leave the iron without supervision when 
it is connected to the power supply.
DO NOT fill the reservoir with water before 
removing the plug from the outlet.
PLEASE NOTE!
Do not use chemical additives, scented 
substances or decalcifiers in the reservoir. 
Failure to comply with the above-mentioned 
regulations will lead to the loss of warranty.
OPERATING 
INSTRUCTIONS
PREPARING FOR FIRST USE
Before first use, remove all labels from the 
soleplate and housing. Plug iron in. Turn the 
iron on, allow to heat up, then turn the iron off. 
Unplug iron.
When using the iron for the first time, you may 
notice a slight emission of smoke and hear some 
sounds made by the expanding plastics. This 
is quite normal and will stop after a short time. 
We also recommend passing the iron over an 
ordinary cloth before using it for the first time.
This GlideLite Iron features advanced One-Temp 
technology. No settings are needed. The iron is 
safe and effective on all fabric types.
FILLING THE RESERVOIR
1.  The reservoir can be filled with ordinary tap 
water. But distilled or demineralized water  
is preferred.
a. Open the water reservoir door.
b. Using a clean measuring cup, slowly fill  
the reservoir until the water reaches the  
max fill indicator. DO NOT OVERFILL.
c. Close water reservoir door.
d. Wipe off any water that may have spilled  
on the outside of the iron with a soft clean  
cloth.
2.  Set the iron on a stable, flat surface. We 
recommend using a quality ironing board  
as the pressing surface. Be sure to give  
yourself enough room to maneuver the  
iron when pressing.
FEDERAL COMMUNICATIONS 
COMMISSION NOTICE
WARNING: Changes or modifications to this 
unit not expressly approved by the party 
responsible for compliance could void the 
user’s authority to operate the equipment. 
This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following 
two conditions: (1) This device may not cause 
harmful interference, and (2) This device must 
accept any interference received, including 
interference that may cause undesired 
operation.
NOTE: This equipment has been tested and 
found to comply with the limits for a Class 
B digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference in a residential installation. 
This equipment generates, uses and can 
radiate radio frequency energy and, if not 
installed and used in accordance with the 
instructions, may cause harmful interference 
to radio communications. However, there is 
no guarantee that interference will not occur 
in a particular installation. If this equipment 
does cause harmful interference to radio or 
television reception, which can be determined 
by turning the equipment off and on, the user is 
encouraged to try to correct the interference by 
one or more of the following measures: 
• Reorient or relocate the receiving antenna. 
• Increase the separation between the 
equipment and receiver. 
• Connect the equipment into an outlet on a 
circuit different from that to which the receiver 
is connected. 
• Consult the dealer or an experienced radio/TV 
technician for help.
SUPPLIER’S DECLARATION  
OF CONFORMITY
Brand: Conair
®
Model No.: GI500
Description: Steam Iron
Responsible Party: Conair LLC, 
1 Cummings Point Road, Stamford, CT 06902 
(203) 351-9000
Standards: FCC Part 15 Subpart B, ANSI  
C63.4-2014 
This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following 
two conditions: 
(1) This device may not cause harmful 
interference, and (2) This device must 
accept any interference received, including 
interference that may cause 
undesired 
operation.
DATE OF ISSUE: 10/18/2022
Produktspecifikationer
| Varumärke: | Conair | 
| Kategori: | Järn | 
| Modell: | GlideLite GI500 | 
| Färg på produkten: | Zwart | 
| Vikt: | 674 g | 
| Bredd: | 257 mm | 
| Djup: | 11.7 mm | 
| Höjd: | 166.5 mm | 
| Internationell säkerhetskod (IP): | IP65 | 
| Batterikapacitet: | 8000 mAh | 
| Blåtand: | Ja | 
| Sensor för omgivande ljus: | Ja | 
| Skärm diagonal: | 10.1 " | 
| Upplösning: | 1920 x 1200 Pixels | 
| Gyroskop: | Ja | 
| Accelerometer: | Ja | 
| Närhetssensor: | Ja | 
| Processorfrekvens: | 2.2 GHz | 
| Processorfamilj: | Qualcomm Snapdragon | 
| Processormodel: | SM4350-AC | 
| Antal processorkärnor: | 8 | 
| Intern lagringskapacitet: | 64 GB | 
| Wi-Fi-standarder: | 802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac), Wi-Fi 6 (802.11ax) | 
| Bluetooth-version: | 5.1 | 
| Generering av mobilt internet: | 5G | 
| GPS: | Ja | 
| Elektronisk kompass: | Ja | 
| Vormfaktor: | Slate | 
| Bakre kameraupplösning (numerisk): | 16 MP | 
| Främre kameraupplösning (numerisk): | 8 MP | 
| Autofokus: | Ja | 
| Typ bakre kamera: | Enkele camera | 
| Inkluderar operativsystem: | Android 12 | 
| Plattform: | Android | 
| Närfältskommunikation (NFC): | Ja | 
| Typ av displayglas: | Gorilla Glass | 
| Ljusstyrka: | 550 cd/m² | 
| Pekskärmstyp: | Capacitief | 
| Batteri/Batterispänning: | 3.85 V | 
| Internminne: | 4 GB | 
| Bluetooth Low Energy (BLE): | Ja | 
| Förvarings media: | Flash | 
| WiFi-standard: | Wi-Fi 6 (802.11ax) | 
| Inkluderar batteri: | Ja | 
| Typ av enhet: | Mobiele tablet | 
| Förvaringstemperatur: | -30 - 70 °C | 
| Säkerhetsfunktioner: | Drop proof, Waterproof | 
| Processorfabrikant: | Qualcomm | 
| Fram kamera: | Ja | 
| Mobil nätverksanslutning: | Ja | 
| Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ C: | 1 | 
| Drifttemperatur (TT): | -20 - 50 °C | 
| Relativ luftfuktighet i drift (VV): | 5 - 95 procent | 
| Batteriteknik: | Lithium-Ion (Li-Ion) | 
| WWAN: | Geïnstalleerd | 
| Robust design: | Ja | 
| Fallbeständig: | 1300 cm | 
Behöver du hjälp?
Om du behöver hjälp med Conair GlideLite GI500 ställ en fråga nedan och andra användare kommer att svara dig
Järn Conair Manualer
                        
                         1 Oktober 2024
                        
                    
                                                            
                        
                         26 September 2024
                        
                    
                                                            
                        
                         10 September 2024
                        
                    
                                                            
                        
                         10 September 2024
                        
                    
                                                            
                        
                         9 September 2024
                        
                    
                                                            
                        
                         9 September 2024
                        
                    
                                                            
                        
                         8 September 2024
                        
                    
                                                            Järn Manualer
- Vivax
- G3 Ferrari
- Polti
- Kernau
- BEKO
- Konig
- Duronic
- Jocca
- Proctor Silex
- Inno-Hit
- Wilfa
- Silvercrest
- Lelit
- Day
- H.Koenig
Nyaste Järn Manualer
                        
                         5 April 2025
                        
                    
                                                            
                        
                         1 April 2025
                        
                    
                                                            
                        
                         1 April 2025
                        
                    
                                                            
                        
                         31 Mars 2025
                        
                    
                                                            
                        
                         31 Mars 2025
                        
                    
                                                            
                        
                         12 Mars 2025
                        
                    
                                                            
                        
                         5 Mars 2025
                        
                    
                                                            
                        
                         5 Mars 2025
                        
                    
                                                            
                        
                         5 Mars 2025
                        
                    
                                                            
                        
                         5 Mars 2025