Crestron DM-RMC-4K-SCALER-C Bruksanvisning
Crestron
Inte kategoriserad
DM-RMC-4K-SCALER-C
Läs gratis den bruksanvisning för Crestron DM-RMC-4K-SCALER-C (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 13 recensioner. Har du en fråga om Crestron DM-RMC-4K-SCALER-C eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
DO GUIDE
DO Connect the Device
Connect the device as required for the application.
Connections, Left Side
Connections, Right Side
NOTE: The DM IN port is a PoDM+ powered device (PD) port and is also compatible with HDBaseT®
PoE+. In order for the device to receive PoDM+, the device requires connection to a DigitalMedia™
switcher or other equipment that has a PoDM+ power sourcing equipment (PSE) port. In order
for the device to receive HDBaseT PoE+, the device requires connection to equipment that has a
corresponding HDBaseT PoE+ PSE port. Any wiring that is connected to a PoDM+ or HDBaseT PoE+
PSE port is for intrabuilding use only and should not be connected to a line that runs outside of the
building in which the PSE is located.
Connection to the included power pack is not required when PoDM+ or HDBaseT PoE+ is used to
power the device.
NOTE: Connection of the CEN-SWPOE-16 to the POE IN ports of DMC-4K-CO-HD output cards in a
DigitalMedia switcher can provide PoDM+ power to up to seven DM-RMC-4K-SCALER-C devices.
NOTE: The LAN port can connect to an Ethernet switch only if the DM IN port does not connect to a
DigitalMedia switcher.
DM-RMC-4K-SCALER-C/DM-RMC-4K-SCALER-C-DSP
4K DigitalMedia 8G+® Receiver and Room Controller with Scaler
DO Install the Device
The Crestron® DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP can be mounted onto a
at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall or a
ceiling.
Mounting onto a Wall
Mounting onto a Rack Rail
The DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP mount onto the front or rear rail of a
rack. Position either the left or the right mounting ange of the device so that the holes align with the
holes in the rack. Then, secure the device to the rack using two rack mounting screws (not included).
Mounting onto a Rack Rail
DO Check the Box
QTY PRODUCT PART NUM.
2 Connector, 4-Pin 2003576
2 Connector, 5-Pin 2003577
1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870
COM:
To RS-232
device
IR 1–2:
To IR
controllable
devices
AUDIO OUT:
To balanced/
unbalanced
stereo line level
audio output
device
RELAY 1–2:
To relay
controllable
devices
Ground
LAN:
10BASE-T/
100BASE-TX
Ethernet to local
network device
DM IN:
From
DM ®
switcher,
transmitter, or other
DM device or from
HDBaseT® device
24 V:
1.25A MAX:
From
included
power pack
HDMI OUT:
To HDMI®
display
Produktspecifikationer
| Varumärke: | Crestron |
| Kategori: | Inte kategoriserad |
| Modell: | DM-RMC-4K-SCALER-C |
Behöver du hjälp?
Om du behöver hjälp med Crestron DM-RMC-4K-SCALER-C ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Crestron Manualer
2 April 2025
2 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
Inte kategoriserad Manualer
- Total
- Flavel
- Powerblade
- Brandson
- Sophos
- Imperia
- A4 Tech
- Vent-A-Hood
- Perkins
- Franke
- Generation
- Mellerware
- LAS
- Hudora
- Nodor
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025