Crestron DMB-4K-I-C Bruksanvisning

Crestron Växla DMB-4K-I-C

Läs gratis den bruksanvisning för Crestron DMB-4K-I-C (2 sidor) i kategorin Växla. Guiden har ansetts hjälpsam av 18 personer och har ett genomsnittsbetyg på 4.1 stjärnor baserat på 9.5 recensioner. Har du en fråga om Crestron DMB-4K-I-C eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

DMB Series

DigitalMedia™ Blades

Installation Guide

To add or replace a DMB I/O blade, perform the following steps and refer to the

illustrations below.

1. Do either of the following:

• If adding an I/O blade, remove the slot cover of an unused input or output slot as

appropriate by loosening the two thumb screws.

• If replacing an I/O blade, disconnect all cables from the blade being replaced,

loosen the two thumb screws that secure the blade to the blade assembly, and

then slide the blade out of the slot.

2. Carefully insert the new blade into the guides at the top and bottom of the selected

slot until the blade is 1/4 inch from the fully seated position.

3. Align the two thumb screws of the blade with the corresponding holes in the blade

assembly, and then push the blade inward until it is fully seated and engages the

chassis backplane.

4. Finger-tighten the two thumb screws to secure the blade—do not overtighten the

screws.

5. Reconnect the cables to the blade.

Input Blade Installation (DM-MD64X64 Shown)

Output Blade Installation (DM-MD64X64 Shown)

Description

DMB blades occupy the DM-MD64X64 and DM-MD128X128 DigitalMedia™ switchers.

This document provides installation instructions for the following:

• Adding or replacing a DMB input/output (I/O) blade

• Replacing the DMB CPU blade

Adding or Replacing a DMB I/O Blade

DMB input blades occupy input slots 1 through 8 of the DM-MD64X64 and input slots

1 through 16 of the DM-MD128X128. DMB output blades occupy output slots 1 through 8

of the DM-MD64X64 and output slots 1 through 16 of the DM-MD128X128. Refer to the

following illustrations for slot locations.

DM-MD64X64 DMB I/O Blade Slots DM-MD128X128 DMB I/O Blade Slots

Additional Resources

Visit the product page on the Crestron® website (www.crestron.com)

for additional information and the latest rmware updates.

CAUTION: DMB I/O blades are susceptible to damage from electrostatic discharge

(ESD). Standard ESD precautions must be followed when handling the blades. Always

wear an ESD wrist strap that is connected to ground, and place blades on grounded

surfaces only.

NOTE: DMB I/O blades are hot swappable; therefore, the blades can be installed

without the need to shut down the DigitalMedia switcher.

Input Slots

1-8

Output Slots

1-8

-B-

Input Slots

1-16

Output Slots

1-16

Thumb

Screws (2)

Thumb

Screws (2)

Produktspecifikationer

Varumärke:	Crestron
Kategori:	Växla
Modell:	DMB-4K-I-C
Färg på produkten:	Zwart
Vikt:	460 g
Bredd:	180 mm
Djup:	142 mm
Höjd:	30 mm
Videolägen som stöds:	1080i, 1080p, 480i, 576i, 720p
Certifiering:	FCC, CE, RoHS\nUL, CUL, CE, PSE, GS\n
Maximal videoupplösning:	- Pixels
On Screen Display (OSD):	Ja
Förvaringstemperatur:	-20 - 60 °C
Förvaringsfuktighet:	20 - 90 procent
Extern anpassning:	Ja
Strömförsörjning via USB:	Nee
Värdgränssnitt:	SDI
Bandbreedte:	2.970 Gbit/s
Driftspänning:	5 V
Drifttemperatur (TT):	0 - 40 °C
Relativ luftfuktighet i drift (VV):	20 - 90 procent
Harmoniserad systemkod (HS):	85176990
Utgångsgränssnitt:	HDMI
Aktiv ström:	2.6 A