CRUX DKGM-49 Bruksanvisning
CRUX
Inte kategoriserad
DKGM-49
Läs gratis den bruksanvisning för CRUX DKGM-49 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 14 personer och har ett genomsnittsbetyg på 3.6 stjärnor baserat på 7.5 recensioner. Har du en fråga om CRUX DKGM-49 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
-Retains factory features in select GM LAN 29 Bit vehicles while functioning with an aftermarket radio.
-Pre-programmed to retain factory Steering Wheel Controls.
-iPhone Voice Recognition (VR) feature from SWC on Kenwood, Pioneer, Alpine and JVC radios.
-Supports Pick Up/End Call, Pick Up and Toggle between 1st and 2nd Incoming call, AVRCP Track, Seek.
-Supports Bose, non-Bose and Y-91 audio systems.
-Provides Factory Rear Seat Entertainment Activation. Requires Cable #CRUX2333A
(sold separately).
-Retains backup sensors / park assist system.
-Retains chime functions.
-EIA color coded wiring for easy installation.
1. *NOT compatible with 2012-Up SUVs/Trucks that are equipped with factory-installed Navigation radios.
2. **NOT compatible with Express and Savana vans that are powered by a diesel engine.
3. Supports Rear Entertainment System with special order harness #CJA2333A (sold separately).
4. DOES NOT support ONSTAR.
GM- Module 49
GM-49 Harness
SWC Cables
Antenna Adaptor
CRUX2543
Dash Kit
Rev.072322
1 / 4
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below.
3.5MM SWC CABLE
Use the proper 3.5 to 4 pin SWC cable for the aftermarket radio being used:
OPTION A is used for ALPINE, CLARION, (JVC and KENWOOD units will use the Blue/Yellow wire).
OPTION B is used for ATOTO, BOSS, DUAL, FAHRENHEIT, JENSEN, POWER ACOUSTIK, PIONEER,
SONY, SOUND STREAM and most OFF-BRAND headunits.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the DK - module has a built-in Bose adaptor that allows the GM 49
proper audio input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin
connector on the harness to the GRAY female 8-pin connector on the - module. The module is also labeled DKGM 49
“Bose” and “Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM-49 module.
BOSE
Connection
Non-BOSE
Connection
2 / 4
Rev.072322
The - module has a potentiometer to adjust the chime volume. It is set at halfway by default. To adjust DKGM 49
the volume, simply use a suitable screwdriver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
You can retain use of the factory backup camera by using the CRUX2543 harness provided in the kit. See below for
connection instructions. (Note: Loose wires may not be needed in the installation.)
NOTE:
Does not retain the factory backup camera on models that show the camera image on the rearview mirror.
A double DIN radio replacement dash kit is included in the kit to make the installation quick and easy. You have the
option of installing a Double DIN or two Single DIN radios. The DKGM-49 kit includes:
Chime
Volume
Adjustment
3 / 4
Rev.072322
Produktspecifikationer
| Varumärke: | CRUX |
| Kategori: | Inte kategoriserad |
| Modell: | DKGM-49 |
Behöver du hjälp?
Om du behöver hjälp med CRUX DKGM-49 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad CRUX Manualer
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
10 Mars 2025
Inte kategoriserad Manualer
- Body Sculpture
- Black Hydra
- VAEMI
- AutoParkTime
- Aputure
- Pippi
- GVision
- HyperIce
- RC Allen
- SHX
- Vaillant
- Murr Elektronik
- E-ast
- MGL Avionics
- ViewCast
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025