Dormakaba Cencon Gen2 Bruksanvisning
Dormakaba
Inte kategoriserad
Cencon Gen2
Läs gratis den bruksanvisning för Dormakaba Cencon Gen2 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 11 recensioner. Har du en fråga om Dormakaba Cencon Gen2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
P/N 2088.0310 Rev. B • 11/12 © copyright 2010-2012 Kaba Mas LLC
Page 1 of 2
CENCON GEN2
Cencon Gen2 Lock to Cencon 4 Software
(Serial to USB) Interface Kit (P/N 201186)
Kit Contents:
A. Interface Box
B. Mini-USB Cable (Cencon PC to Interface Box)
C. 10-pin Serial Cable (Gen2 Lock to Interface Box)
Compatibility:
The Interface Kit is designed for use with Cencon Generation 2 (Gen2) locks
in conjunction with the Cencon 4 software, version 4.0.5 and higher.
Purpose:
The Interface Kit allows the Gen2 lock to be programmed or data to
be retrieved from the lock via a direct communication to the Cencon 4
software. Rather than transporting keys from the PC to the lock key reader
and back, the Interface Kit allows a direct wired connection from the 10-pin
serial connector on the back cover of the Gen2 locks with a USB port on
the Cencon 4 PC. Aside from the time-saving aspect of using the Interface
Box, another benefit is the unique reporting capability provided by using
this device. The Lock Status Report shows various items such as bolt status and temperature. A full Lock Audit (i.e., all available audit
records in the lock) can be obtained via the direct link through the Interface Box. This is an improvement over the traditional method of
retrieving audit records with the red SA key where the number of records may be truncated due to the limitation of the memory in
the key.
Direct “Serial Connect” operations using the Interface Kit include:
• Activate FLM, Route, and Bank modes (including setting initial Bank mode users)
NOTE: Activating a Mode will require that the change key be inserted into the lock back cover. (See photo below.)
• Change the Access Requirement type for a mode between Single
and Dual
• View, Add, or Delete Bank mode users
• Close an FLM or Route mode open call on the software (lock powers
up “IPI”)
• Resynchronize the software with the FLM or Route mode of the lock
• Resynchronize the User List in software for Bank Mode with the lock
• Set Time Delay and Open Time Window for Bank Mode
• Shelve FLM, Route, and Bank modes
• Set Lock Clock and Time Zone Daylight Savings Time Table
• View Lock Status Report and Lock Audit Report
Please refer to the Cencon 4 Reference Manual (found at http://www.kaba-
mas.com/pdf/technical/2071.127Cencon4RefManA.pdf or on the install
CD), Section 3.1.7 “Lock Operations with Serial Connect”, for details on
each of these operations.
Driver Install instructions for the Cencon Interface Box:
WARNING: DO NOT plug in the USB device before installing the driver.
The PC that is running Cencon 4 should be able to obtain a connection to the internet to download this driver. If the PC does not have
a connection, save the driver to a disc or USB drive to transfer it to the Cencon 4 PC.
The Interface Kit uses FTDI Device FT232R. A copy of the driver installation for the device is available at
http://www.ftdichip.com.
InstructIon sheet
A.
B.
C.
Interface Kit parts.
Always wear a grounding strap when handling the back cover.
Produktspecifikationer
| Varumärke: | Dormakaba |
| Kategori: | Inte kategoriserad |
| Modell: | Cencon Gen2 |
Behöver du hjälp?
Om du behöver hjälp med Dormakaba Cencon Gen2 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Dormakaba Manualer
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
Inte kategoriserad Manualer
- Nanni
- Medel
- Newstar
- Envertech
- Babymoov
- Spear & Jackson
- Gree
- ALM
- Heckler Design
- SereneLife
- Speco Technologies
- KKT Kolbe
- Bēm Wireless
- Bixolon
- RIDGID
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025