Dormakaba La Gard 3390 Bruksanvisning
Dormakaba
Inte kategoriserad
La Gard 3390
Läs gratis den bruksanvisning för Dormakaba La Gard 3390 (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 3.8 stjärnor baserat på 8 recensioner. Har du en fråga om Dormakaba La Gard 3390 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
(P/N) 709.058 Rev H
08/18 • © copyright 2008-2018 1
Read guide completely before beginning installation.
SAFEGUARDS FOR MOUNTING
1. Complete all welds to the safe prior to installation of the lock.
2. Keep metal dust, filings, etc. away from the lock.
3. Never oil, grease, lubricate or paint the lock.
4. If applicable, keep cables away from sharp edges and moving parts.
5. If applicable, never carry the lock by the cable.
Group 2M Mechanical Lock (3390 Series)
Hardware Pack, US (P/N 704004) Includes
2. Spline Key (P/N 1712)
3. Mounting Screws (P/N 2930 - Qty. 2)
4. Mounting Screw (P/N 1819)
5. Change Key (P/N 1307)
6. Insert Cover (P/N 705002)
Hardware Pack, Metric (P/N 704003) Includes
2. Spline Key (P/N 1712)
3. Mounting Screws (P/N 705006 - Qty. 2)
4. Mounting Screw (P/N 205014)
5. Change Key (P/N 1307)
6. Insert Cover (P/N 705002)
DESIGN PARAMETERS FOR MECHANICAL COMBINATION LOCKS
1. Bolt dimensions (nominal): .312 inches x 1.000 inches/8 x 25.4mm
2. Bolt movement (nominal): .465 inches/11.8mm
3. Bolt extension: .465 inches/11.8mm
4. Maximum load movable by the bolt: 5 lbs. (22N)
NOTE: LA GARD dead bolt locks may not open if more than 5 lbs. (22N) of force is
applied to the end or side of the bolt.
5. Maximum load against bolt when thrown (all directions): 224.8 lbs. (1kN)
6. The lock can be fitted to safes or vault doors of any material.
NOTE: As is the case with all mechanical and electronic locking devices, the container and boltworks must be designed to
protect the lock from all possible attack methods and angles, including front side, side walls, and back side of the lock.
Prepare for New Installation of the Lock (If Required)
1. Use the template provided to establish the exact locations (relative to the spindle hole)
of the mounting holes for the lock assembly.
2. The spindle hole diameter can be a minimum of .406” (10.3mm) to a maximum of .438”
(11.1mm). The .406” (10.3mm) diameter is recommended. Spindle hole must be
deburred.
3. The dial assembly mounting screws require drilled and tapped holes to 3/8” (9.5mm)
depth if possible (minimum 1/4” or 6.4mm depth required.) Drill either the two
horizontal mounting holes or the two vertical holes.
4. When mounting the lock unit (i.e., integrating it in a boltwork), make sure that the lock
bolt has clearance to freely move to its end positions and that the shifting force works
only in the axial direction (direction of movement). Lateral forces should not be exerted
on the lock.
INSTALLATION INSTRUCTIONS
Figure 2
DOOR
Total Mounting Thickness
(plus .875")
Optional hardplate
or mounting bracket
Figure 3
1
5
6
2
4
3
Figure 1
MECHANICAL
3390 SERIES GROUP 2M LOCK
Produktspecifikationer
| Varumärke: | Dormakaba |
| Kategori: | Inte kategoriserad |
| Modell: | La Gard 3390 |
Behöver du hjälp?
Om du behöver hjälp med Dormakaba La Gard 3390 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Dormakaba Manualer
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
Inte kategoriserad Manualer
- Weltevree
- Macally
- Suunto
- Lowepro
- Eufy
- Tenda
- Bitspower
- Lexicon
- Q Acoustics
- Richgro
- QUIO
- Pentax
- Atlantis Land
- Jane
- Gustavsberg
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025