Electro Harmonix Neo Clone Bruksanvisning
Electro Harmonix
Inte kategoriserad
Neo Clone
Läs gratis den bruksanvisning för Electro Harmonix Neo Clone (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 8.5 recensioner. Har du en fråga om Electro Harmonix Neo Clone eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
NEO CLONE
FULL CHORUS
Congratulations on your purchase of the Electro Harmonix ! The Neo Clone Neo
Clone is a compact battery operated Chorus effects pedal that features DEPTH and
RATE controls, True Bypass and an LED function indicator. To produce the Chorus
effect, the bends the frequency slightly from the input source and mixes Neo Clone
this altered signal with some direct unaffected signal. The combination produces a
doubling effect.
-OPERATING INSTRUCTIONS-
Plug your guitar into the jack and your amp into the jack, which is the INPUT AMP
Neo Clone’s output jack. Please note that as long as anything is plugged into the
INPUT, a drain is placed on your battery. It is recommended that you disconnect
the when the unit is not in use to extend battery life. INPUT
The DEPTH switch controls the amount of frequency change that occurs in the
altered signal. The speed of Chorus modulation is controlled by the knob. RATE
The red indicates when the effect is switched on. The footswitch toggles LED
between the Chorus effect and true bypass.
- - POWER
Power from the internal 9-volt battery is activated by plugging into the jack. INPUT
The input cable should be removed when the unit is not in use to avoid running down
the battery. If a battery eliminator is used, the Neo Clone will be powered up as long
as a wall-wart is plugged into the wall.
The barrel connector on the front of the Neo Clone is for a 9-volt battery eliminator
capable of delivering at least 25 mA of current. The optional 9V power supply from
Electro-Harmonix is 9.6DC-200BI (same as used by Boss™ & Ibanez™) 9.6 Volts DC
200mA. The inner ring of the 9-volt battery eliminator must be negative, the outer
ring positive. The unit’s battery may be left in or taken out when the eliminator is in
use. The actual current draw of the Neo Clone is 12 mA.
To change the 9-volt battery, you must remove the 4 screws on the bottom of the
Neo Clone. Once the screws are removed, you can take off the bottom plate and
change the battery. Please do not touch the circuit board while the bottom plate is off
or you risk damaging a component.
The input impedance presented at the Input Jack is . The output impedance at 220k
the Amp Jack is 1k .
Produktspecifikationer
| Varumärke: | Electro Harmonix |
| Kategori: | Inte kategoriserad |
| Modell: | Neo Clone |
Behöver du hjälp?
Om du behöver hjälp med Electro Harmonix Neo Clone ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Electro Harmonix Manualer
2 April 2025
2 April 2025
2 Januari 2025
30 December 2025
30 December 2025
30 December 2025
30 December 2025
5 December 2024
24 September 2024
24 September 2024
Inte kategoriserad Manualer
- Hestan
- Deaf Bonce
- MoFi
- Icon
- JLCooper
- Germania
- BlueBuilt
- Levoit
- Bestron
- ACOPower
- Goodway
- DVDO
- Maytronics
- Outwell
- Roadinger
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025