Electro Harmonix Switchblade+ Bruksanvisning
Electro Harmonix
Inte kategoriserad
Switchblade+
Läs gratis den bruksanvisning för Electro Harmonix Switchblade+ (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 32 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 16.5 recensioner. Har du en fråga om Electro Harmonix Switchblade+ eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
SWITCHBLADE+
Deluxe Channel Selector
Congratulations on your purchase of the Electro-Harmonix ! With a fully SWITCHBLADE+
passive audio path and active LED indication, the provides a simple and SWITCHBLADE+
versatile interface for routing your signal.
Controls – –
A/B Footswitch (LED) –Press this switch to route the input signal to either OUT A (Red
LED) or OUT B (Green LED).
A+B Footswitch (LED) – Press this switch to route the input signal to both OUT A and
OUT B. When A+B is engaged (Red LED), the A/B Footswitch has no effect on the signal
path.
– – I/O
INPUT –Connect the output of your instrument or another effects pedal to this jack.
TUNER –Connect this jack to the input of a tuner device or another effects pedal. This
jack is hardwired to the INPUT jack and provides a direct output regardless of the state of
the unit.
OUT A Connect this jack to the input of an amplifier or the input of another effects –
pedal. Depending on the state of the A/B and A+B controls, this jack will output either the
direct input signal or no signal. When the A/B LED is lit red or the A+B LED is lit up, OUT A
is selected.
OUT B Connect this jack to the input of an amplifier or the input of another effects –
pedal. Depending on the state of the A/B and A+B controls, this jack will output either the
direct input signal or no signal. When the A/B LED is lit green or the A+B LED is lit up, OUT
B is selected.
– Power -
The can be powered by a 9V battery or a 9VDC battery eliminator SWITCHBLADE+
capable of delivering at least 16mA. The optional 9V power supply from Electro-Harmonix
is 9.6DC-200BI (same as used by Boss® & Ibanez®) 9.6 Volts DC 200mA. The power
supply must have a barrel connector with center negative.
The SWITCHBLADE+ can also operate without power, since the audio path is fully
passive. With no power, however, the LED indication will not function.
When A+B is engaged, the input impedance at the INPUT jack is equal to 50kΩ in parallel
with the combined input impedances of the devices connected to the TUNER, OUT A, and
OUT B jacks. When A+B is not engaged, the input impedance at the INPUT jack is equal
to 100kΩ in parallel with the combined input impedances of the devices connect to the
TUNER jack and OUT A or OUT B.
Produktspecifikationer
| Varumärke: | Electro Harmonix |
| Kategori: | Inte kategoriserad |
| Modell: | Switchblade+ |
Behöver du hjälp?
Om du behöver hjälp med Electro Harmonix Switchblade+ ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Electro Harmonix Manualer
2 April 2025
2 April 2025
2 Januari 2025
30 December 2025
30 December 2025
30 December 2025
30 December 2025
5 December 2024
24 September 2024
24 September 2024
Inte kategoriserad Manualer
- Hapro
- Emerio
- Novation
- Fagor
- Ferroli
- Lowrance
- Sharp
- Pippi
- Adastra
- Welltech
- Elbro
- Eldom
- HQ
- Taco Tuesday
- Kyoritsu
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025