Electro Harmonix Pico Rerun Bruksanvisning
Electro Harmonix
ej kategoriserat
Pico Rerun
Läs gratis den bruksanvisning för Electro Harmonix Pico Rerun (2 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 26 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 13.5 recensioner. Har du en fråga om Electro Harmonix Pico Rerun eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
RERUN
User Manual
Tape Delay
RERUN
User Manual
Tape Delay
Tails and Analog Bypass Selection
The Rerun allows you to choose between two
bypass modes:
Analog: the bypass signal is fully analog; the
delay effect instantly mutes upon entering
bypass.
Tails: the repeats of the delay effect continue
to decay naturally upon entering bypass; no new
audio enters the delay block; bypass is digital.
Tails bypass is selected by default from the facto-
ry. To activate Analog bypass, do the following:
1. Press and hold the TYPE push button.
2. After two seconds, the LED enters Party Mode,
where it rapidly cycles through the three LED
colors.
3. Release the button; Analog bypass is now
active.
4. Repeat this same procedure to change back
to Tails bypass.
The bypass mode setting is remembered through
power-cycles so you can set it and forget it.
Maximum Feedback Self-Oscillation
Turn the FDBK knob up to maximum to achieve
runaway self-oscillation. When Tails bypass
mode is enabled, you can also activate maxi-
mum feedback by pressing and holding the
footswitch:
1. Press-and-hold the footswitch.
2. After 500ms, the LED begins flashing through
all three colors. Maximum Feedback is now
active.
3. Release the footswitch to stop self-oscillation
and return the feedback setting to the current
position of the FDBK knob.
Questions about this product? Email: info@ehx.com
Tails and Analog Bypass Selection
The Rerun allows you to choose between two
bypass modes:
Analog: the bypass signal is fully analog; the
delay effect instantly mutes upon entering
bypass.
Tails: the repeats of the delay effect continue
to decay naturally upon entering bypass; no new
audio enters the delay block; bypass is digital.
Tails bypass is selected by default from the facto-
ry. To activate Analog bypass, do the following:
1. Press and hold the TYPE push button.
2. After two seconds, the LED enters Party Mode,
where it rapidly cycles through the three LED
colors.
3. Release the button; Analog bypass is now
active.
4. Repeat this same procedure to change back
to Tails bypass.
The bypass mode setting is remembered through
power-cycles so you can set it and forget it.
Maximum Feedback Self-Oscillation
Turn the FDBK knob up to maximum to achieve
runaway self-oscillation. When Tails bypass
mode is enabled, you can also activate maxi-
mum feedback by pressing and holding the
footswitch:
1. Press-and-hold the footswitch.
2. After 500ms, the LED begins flashing through
all three colors. Maximum Feedback is now
active.
3. Release the footswitch to stop self-oscillation
and return the feedback setting to the current
position of the FDBK knob.
Questions about this product? Email: info@ehx.com
Produktspecifikationer
| Varumärke: | Electro Harmonix |
| Kategori: | ej kategoriserat |
| Modell: | Pico Rerun |
Behöver du hjälp?
Om du behöver hjälp med Electro Harmonix Pico Rerun ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Electro Harmonix Manualer
2 Oktober 2025
10 Augusti 2025
9 Augusti 2025
9 Augusti 2025
7 Augusti 2025
4 Augusti 2025
30 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
ej kategoriserat Manualer
- Stiebel Eltron
- Berner
- Cadco
- Reloop
- MIFAB
- Sun Dolphin
- Westinghouse
- Aqua Joe
- Brizo
- Draper
- Vonroc
- ResMed
- Vishay
- MBM
- Karcher
Nyaste ej kategoriserat Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025