Emko EAOM-36 Bruksanvisning

Emko ej kategoriserat EAOM-36

Läs gratis den bruksanvisning för Emko EAOM-36 (8 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 3.7 stjärnor baserat på 2 recensioner. Har du en fråga om Emko EAOM-36 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF
Sida 1/8
Features
Controls
FailMonitoring
EAOM-36ManualStartUnitusemicroprocessorbasedtechnologytoprovideintegratedmanualstartand
faultprotectioninawiderangeofengineapplications. Themoduleishousedin72x72DINsize.Themoduleis
usedtostartandstoptheengine,indicatingtheoperationalstatusandfaultconditions. Automaticallyshutting
downtheengineandindicatingtheenginefailurebyaflashingLED.Usercancontroltheengineviaatwoposition
keyswitchandpushbuttonsmountedonthefrontpanelorwithremoteinput.
parameterP00).
Themodulecanconnectdirectlywithengine,thankstohighcurrentrelayoutputs.
Themodulehastwofeatureforfuel.Oneof“energizetorun”theother“energizetostop”.Usercanselectthe
featurefromprogramparameters.
The module protect the engine against fault conditions. If a fault condition occurred, the module indicate the fault
condition and shut-down the engine.
If the key switch is OFF position the module has zero power consumption to save energy. The module energizes
when the key switch position is getting ON position. If Satart button is pressed, the Conf. Out relay output (if selected
preheat output) will activate until the preheat delay is expired.
Press Start button for starting the engine. When engine is running, module will stop the cranking.
Press Stop button for stoping the engine. After pressing the stop button, the engine will keep running until cooling
time(P21) is expired.
Also the module has remote start facility. Please select suitable type of remote start for your application from
program parameters. If remote start input is active the module will start the engine. If remote start is passive the unit will
stop the engine after cooling time is expired.
The module will check the alarms after safety on timer is expired.
Under one of this fault conditions the module will stop the engine;
- Over speed (generator application),
- Under speed(generator application),
- High Temperature,
- Low Oil Pressure,
- Shutdown (if one of conf. input selected shutdown and activated).
To reset the fault, turn the key switch to the OFF position for a few seconds.
The Charge Failure is a warning alarm so the engine continue to work under this failure condition. Also this input
supplying charge alternator excitation current.
Shutdown the engine;
If the engine fuel type is “energize to stop”, press Stop button until the engine comes to rest. After that select OFF
position of the key switch.
If the engine fuel type is “energize to run”, select OFF position of the key switch.
On the Fire Pump application; If a fault condition occurred, the module will not stop the engine.
The engine will be stopped only when the stop button was pressed or the remote stop signal was detected.
Important note:
Manual and Remote Start with Key Switch, 72x72 DIN SizeUnit
DesignedForGenerator,Pump&FirePump Applications
Remotestart/stopcapabilitywithzeropowerconsumption
Enginestartandstop
Automaticshutdownonfaultcondition
Providesalarmandstatusinformation
Alarmandshutdowninputs
Provideschargealternatorexcitationcurrent
Lamptestfunction
Oilpressure
Enginetemperature
Overspeed&Underspeed(generatorapplication)
Chargingalternator
Conf.Input-1&2
Enginefuelorstopsolenoid
Startermotor
Preheat,simulatefuelsolenoid,externalalarm
horn,alarmorloadcontactorout
IntroductionBrochure.ENGEAOM-36R01V0612/17
START
Hz./
RPM
CHARGINGFAIL
~ ~
~~~~
HIGHTEMPERATURE
LOWOIL PRESSURE
FAILEDTOSTART
SPEED
FAILURE
0
I
EAOM-36
STOP
RPM
ProgramParametersforGenerator Application
1-Whenthe-BATTERY appliedtoRem.startinput(terminal-11),
theenginestartcranking.(leavekeyswitch“1”position)
2-Whenthe+BATTERY appliedto+BAT input(terminal-3),
theenginestartcranking.(leavekeyswitch“1”position)
0-Disable. Thestart/stopbutonisused. (leavekeyswitch“1”position)
ProgNo
ParameterName
Unit Limits Default
P 00
ApplicationSelection(Generator,Pump,FirePump) GEn,PUP,FPU GEn
P 01
P 02
P 04
P 06
P 07
P 08
P 09
FrequencyLowerLimit
FrequencyUpperLimit
-
Hz.
Hz.
30.0-75.0
30.0-75.0
47.0
53.0
HornDuration Sec. 0=Cont.1-999 30
Nominal AlternatorFrequency Hz. 30.0-75.0 50.0
NominalSpeed Rpm 500-5000 1500
Stop/FuelSolenoidSelection - StoP -FUEL FUEL
StopSolenoidEnergising Time Sec. 1-99 20
CrankDisconnectonGen.Frequency Hz. 25.0-75.0 30.0
P 10
CrankDisconnectonCharge AlternatorVoltage - diS-EnAb diS
P 11
CrankDisconnectonOilPressure
- 0=diS1-2 1
P 12
NumberofStarting Attempts Number 1-10 3
P 13
Starting AttemptDuration Sec. 5-99 5
P 14
OilPressureBypass Time Sec. 0-99 30
SafetyOnDelay
P 15
Sec. 0-99 10
FrequencyFaultControlDelay Sec. 0.0-10.0 3.0
P 16
P 17
EngineRunning TimeValue&NewEngineRunning Time Hour 0-9999 0
RemoteStartSelection:
P 18
P 19
Conf.Out Type:
- diS
-
0-4
P 20
Conf.Input1
0- Onlyhorntemporary,observationcontinuously
1- Onlyhornpermanent,observationcontinuously
2- Enginestop,observationcontinuously
3- Onlyhorntemporary,observationwhileenginerunning
4- Onlyhornpermanent,observationwhileenginerunning
5- Enginestop,observationwhileenginerunning
P 22
Conf.Input2
0- Onlyhorntemporary,observationcontinuously
1- Onlyhornpermanent,observationcontinuously
2- Enginestop,observationcontinuously
3- Onlyhorntemporary,observationwhileenginerunning
4- Onlyhornpermanent,observationwhileenginerunning
5- Enginestop,observationwhileenginerunning
Password 0-9999 0-
P 03
P 05
0-5 0
0-5 0
-
-
0=diS1-2
2
Manual and Remote Start with Key Switch, 72x72 DIN SizeUnit
!
Warning:P16RemoteStartSelectionparameteroption‘2’ cannotbeusedwithstopsolenoidtypegenerators.
Cooling Time Sec. 0(dis)-3600 0
P 21
0- AlarmOut,1-HornOut,
2-PreheatOut,3-SimulateFuelSolenoidOut,
4-LoadContactorOut
0
0-Disable
1-Enable(always)
2-Enable(onlybeforestart)
ProgramParametersforPump(FirePump) Applications
ProgNo
ParameterName
Unit Limits Default
P 00
ApplicationSelection(Generator,Pump,FirePump) GEn,PUP,FPU PUP
P 06
P 08
P 09
-
Stop/FuelSolenoidSelection - StoP -FUEL FUEL
StopSolenoidEnergising Time Sec. 1-99 20
P 10
CrankDisconnectonCharge AlternatorVoltage - diS-EnAb diS
P 11
CrankDisconnectonOilPressure
- 0=diS1-2 1
P 12
NumberofStarting Attempts Number 1-10 3
P 13
Starting AttemptDuration Sec. 5-99 5
OilPressureBypass Time Sec. 0-99 30
SafetyOnDelay
P 15
Sec. 0-99 10
P 16
P 17
EngineRunning TimeValue&NewEngineRunning Time Hour 0-9999 0
P 18
P 19
Conf.Out Type
- diS
- 0-4 0
Conf.Input1
0- Onlyhorntemporary,observationcontinuously
1- Onlyhornpermanent,observationcontinuously
2- Enginestop,observationcontinuously
3- Onlyhorntemporary,observationwhileenginerunning
4- Onlyhornpermanent,observationwhileenginerunning
5- Enginestop,observationwhileenginerunning
Conf.Input2
0- Onlyhorntemporary,observationcontinuously
1- Onlyhornpermanent,observationcontinuously
2- Enginestop,observationcontinuously
3- Onlyhorntemporary,observationwhileenginerunning
4- Onlyhornpermanent,observationwhileenginerunning
P 05
0-5 0
0-5 0
-
-
0=diS1-2
HornDuration Sec. 0=Cont.1-999 30
P 20
P 22
5- Enginestop,observationwhileenginerunning
Password 0-9999 0-
1-Whenthe-BATTERY appliedtoRem.startinput(terminal-11),
theenginestartcranking.(leavekeyswitch“1”position)
2-Whenthe+BATTERY appliedto+BAT input(terminal-3),
theenginestartcranking.(leavekeyswitch“1”position)
0-Disable. Thestart/stopbutonisused. (leavekeyswitch“1”position)
RemoteStartSelection:
Manual and Remote Start with Key Switch, 72x72 DIN SizeUnit
3
Cooling Time Sec. 0(dis)-3600 0
P 21
0- AlarmOut,1-HornOut,
2-PreheatOut,3-SimulateFuelSolenoidOut,
4-LoadContactorOut
0-Disable
1-Enable(always)
2-Enable(onlybeforestart)

Produktspecifikationer

Varumärke: Emko
Kategori: ej kategoriserat
Modell: EAOM-36

Behöver du hjälp?

Om du behöver hjälp med Emko EAOM-36 ställ en fråga nedan och andra användare kommer att svara dig


ej kategoriserat Emko Manualer

Emko

Emko SMR1P1-00-00-01-00 Bruksanvisning

20 Juni 2025
Emko

Emko ESM-3721HT Bruksanvisning

20 Juni 2025
Emko

Emko DT-9910 Bruksanvisning

20 Juni 2025
Emko

Emko EAOM-19 Bruksanvisning

20 Juni 2025
Emko

Emko ESM-1500 Bruksanvisning

20 Juni 2025
Emko

Emko EAOM-36 Bruksanvisning

20 Juni 2025
Emko

Emko EAOM-9 Bruksanvisning

20 Juni 2025
Emko

Emko ESM-3712-HC Bruksanvisning

20 Juni 2025
Emko

Emko ESM-9995 Bruksanvisning

20 Juni 2025
Emko

Emko IPERTU Medium Lite Bruksanvisning

20 Juni 2025

ej kategoriserat Manualer

Nyaste ej kategoriserat Manualer

Razer

Razer Emote Display Bruksanvisning

20 Juni 2025
Omega

Omega OC70TZ Bruksanvisning

20 Juni 2025
Omega

Omega Crime Guard IM01-GMDL7X Bruksanvisning

20 Juni 2025
Infinity

Infinity Kappa XE-2 Bruksanvisning

20 Juni 2025
Infinity

Infinity Beta XP One Bruksanvisning

20 Juni 2025
Baccarat

Baccarat The Toasty Slice Bruksanvisning

20 Juni 2025
Kramer

Kramer VS-84HN Bruksanvisning

20 Juni 2025
Kramer

Kramer RK-KVM-2U Bruksanvisning

20 Juni 2025
Kramer

Kramer AFM-20DSP-LE Bruksanvisning

20 Juni 2025
Glem Gas

Glem Gas GTIB63BK Bruksanvisning

20 Juni 2025