Ernitec 0070-08214 Bruksanvisning
Ernitec
övervakningskamera
0070-08214
Läs gratis den bruksanvisning för Ernitec 0070-08214 (2 sidor) i kategorin övervakningskamera. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 8 recensioner. Har du en fråga om Ernitec 0070-08214 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Special Announcement
, For more i nform ation please refe r to website.
Fully u nderstand this do cument before using this device,
and strictly observe rules in this document when using this
device. If you insta ll this device in public pla ces, provide the
tip "You have entered the area of electronic surveillance" in
an eye-catching place. Failure to correctly use electrical
products may cause fire and severe injuries.
ŸStrictly observe installation requirements when installing
the device. The manufacturer shall not be held responsible
for device damage caused by users' non-conformance to
these requirements.
ŸStrictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard
when installing and using this device. Otherwise, this
device may be d amaged.
ŸUse accessories delivered with this device. The voltage
must meet input voltage requirements for this device.
ŸIf this device is installed in places with unsteady voltage,
ground this device to discharge h igh energy such as
electrical surges in order to prevent the power supply from
burning out.
ŸWhen this device is in use, ensure that no water or an y
ŸAvoid heavy loads, in tensive shakes, and soaking to
preve nt damages during transportation and storage. The
warranty does not cover any device damage that is caused
durin g secondary p ackaging and transportation after the
original packaging is taken apart.
ŸProtect this d evice from fall-down and intensive strikes,
keep the device away from magnetic field interference, and
do not install the device in places with shaking surfaces or
under shocks.
ŸClean the device with a soft dry cloth. For stubborn dirt, dip
the cloth into slight neutral clea nser, gently wipe the dirt
with the cloth, and then dry the device.
ŸDo not jam the ventila tion opening. Follow the installation
instructions provided in this document when installing the
device.
ŸKeep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
ŸKeep the device away from moist, dusty, extremely hot or
cold places, or places with stron g electric radiation.
ŸIf the device is installed outdoo rs, take insect- and
moisture-proof measures to avoid circuit board corrosion
that can affect monitoring.
ŸRemove the power plug if the device is idle for a long time.
ŸBefore unpacking, check whether the fragile sticker is
damaged. If the fragile sticker is damaged, contact
customer services or sales personnel. The manufacturer
shall not be held responsible for any artificial damage of the
fragile sticker.
ŸAll complete products sold by the manufacturer are
delivered along with nameplates, quick setup guide and
accessories after strict inspection. The manufacturer shall
not be he ld responsible for counterfeit products.
ŸThe manufacturer will update this manual according to
product function enhancement or changes and regularly
update the software and hardware described in this manual.
Update information will be added to new versio ns of this
manual without prior notice.
ŸThis manual may contain misprints, technology information
that is not accurate enough, or product function and
operation description that is slightly inconsistent with th e
actual prod uct, the final interpretation of company is as a
standard.
ŸThis manual is only for reference and does not ensure that
the information is to tally consistent with the actual prod uct.
For con sistency, see the actual product.
Precautions
Open the package, check the appearance of product for no
obvio us damage, and confirm the item list for table 1-1 is
consistent.
Table 1 1- Packing list
2.1 Device Ports
Different devic es may have differe nt ports and multi-head
cable; Please refer to the ac tual product.
NOTE
NOTE
NOTE
liquid flows into the device. If water or liquid unexpectedly
flows into the device, immediately power off the device and
disconnect all cables (such as power cables and network
cable s) from this device.
ŸDo not focus strong light (such as lighted bulbs or sunlight)
on this device. Otherwise, the service life of the image
sensor may be shortened.
ŸIf this device is installe d in places where thunder an d
lightning frequently occur, ground the device nearby to
discharge high energy such as thunder strikes in order to
preve nt device damage.
It alerts you to moderate dangers which, if not
avoid ed, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable
results.
It provides additional information.
NOTE
CAUT ION
WARNING
WARNING
CAUTION
1
Device Structure2
Open Package Examination
Bullet Network Camera
Quick Setup Guide
Installation location sticker
Accessory package
Component Quantity Remark
1
1
1
Figure2 1- Multi-head cable
1
Table 2-1 Multi-head cable description
Figure 2 3 Install SD card-
Port
1
2
3
4
5
IN
OUT
GG
Connects to a standard Ethernet
cable or PoE . The green light is on,
the network connection is normal;
the yellow light flashes when the
data is transmitted. Some models
maybe not have the lights; Please
refer to the actual product.
Connects to an external audio
device such a s a speaker.
Applied for
camera with
audio
function
Receives an a nalog audio s ignal
from devices such as a sound
pickup device.
Connects to a 12V direct current
(DC) power supply.
Alarm outpu t COM Applied for
alarm
function
Alarm outpu t terminal
Alarm input COM
Alarm input terminal
2
1
ID
3
5
Network
access port
Support PoE
supply.
Core Description Remark
Audio output
Power suppl y
(DC 12V)
Audio input
port
OUT
IN
G
G
4
Reset PWR SD
95
30
2-1/4UNC x8
4-φ4.5
98
70
70
100
275
107
273~~303 ajustable
2.3 Fill light settings
Camera’s fill lig ht has four modes, they are intelligen t dual light (
current fill light will switch to warm li ght after an al arm is triggered,
and will switch back to the original fill l ight for 30s after the alert is
released.), warm light, infrared la mp and none (Cl ose the fill light
and the color of image will stay in previous mode).
The different cam eras can be set d ifferent fill light modes, pl ease
set fill light modes according to the actual scene.
Day mode: It can be used in the scene with sufficie nt ambient li ght
for 24 hours, do not turn on the fill light, and the image is in color.
Night mode: it can be used in the scene where there is insuffici ent
ambient light for 24 hours , turn on the fil l light (it can b e selected
according to the four mode s of the fill light).
Auto mode: Automatically switch the fill light mode ac cording to
the luminance of the environment.
Timing mode: Set the start and end time of the day, this time
period is day m ode for camera.
Different devic es may have differe nt fill lights; Please refer to
the actual product.
NOTE
2 2 Camera Dimensions.
Figure 2 2 -Dimensions Unit: mm （ ）
Differe nt devices may have different dimensions; Please
refer to the actual product.
Deimos Network Camera
5MP Fix Lens – day & night colour
Quick Setup Guide
Item no.: 0070-08214
Produktspecifikationer
| Varumärke: | Ernitec |
| Kategori: | övervakningskamera |
| Modell: | 0070-08214 |
Behöver du hjälp?
Om du behöver hjälp med Ernitec 0070-08214 ställ en fråga nedan och andra användare kommer att svara dig
övervakningskamera Ernitec Manualer
23 September 2024
22 September 2024
20 September 2024
11 September 2024
11 September 2024
11 September 2024
11 September 2024
10 September 2024
9 September 2024
9 September 2024
övervakningskamera Manualer
- Flamingo
- Milestone Systems
- Hamlet
- Astak
- SPC
- Stabo
- SecurityMan
- Kogan
- Avanti
- DIO
- Caliber
- Moog
- WisuAlarm
- Chacon
- Indexa
Nyaste övervakningskamera Manualer
23 Oktober 2025
20 Oktober 2025
20 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
14 Oktober 2025
14 Oktober 2025