EXSYS EX-11092-2 Bruksanvisning

EXSYS nätverkskort/adapter EX-11092-2

Läs gratis den bruksanvisning för EXSYS EX-11092-2 (2 sidor) i kategorin nätverkskort/adapter. Guiden har ansetts hjälpsam av 34 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 17.5 recensioner. Har du en fråga om EXSYS EX-11092-2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

6 5

Die EX-11092-2 ist eine USB 3.2 Gen 1 PCIe Karte. Sie ist mit zwei externen Buchsen ausge-

stattet, die jeweils 900mA Strom zu Verfügung stellen. Die EX 2 unterstützt die volle -11092-

Leistung von 900mA an beiden externen Buchsen ohne das Sie zusätzlichen Strom vom PC-

Netzteil benötigen. Sie unterstützt alle PCIe Slots von x1 bis x16. Der PCI Express Bus unter--

stützt optimal die Leistung des schnellen Renesas Chipsatz. Die EX 2 gewährleistet so -11092-

eine sichere Datenübertragung und exzellente Performance von bis zu 5Gbit pro Sekunde! Sie

unterstützt alle USB Anschlüsse von 1.1 bis 3.2. Zusätzlich bietet die EX 2 Ihnen die -11092-

Möglichkeit das USB Kabel an die UBS Buchsen der Karte zu verschrauben.

Kompatibilität: PCI Express p1-x1 bis x16 -

Betriebssysteme: Windows XP / Vista / 7 / 8.x / 10 / 11 / Server 20xx / Linux / Mac

Anschlüsse: 2x USB 3.2 Gen 1 A Buchse (verschraubbar), 1x 4 Pin Molex Power - -

Anschluss

Lieferumfang: 2, Low Profile Bügel, Treiber CD, Anleitung EX-11092-

Zertifikate:

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.5 / 26.02.24

E 1109

ANSCHLÜSSE & JUMPER EINSTELLUNG

2x USB 3.2 Gen 1 A Buchse (verschraubbar)-

USB 3.2 Gen 1 Buchse:

USB 2.0 Pin s‘

Pin Signal

1 VCC

2 DATA -

3 DATA+

4 GND

USB 3.2 Pin s‘

Pin Signal

5 SSTX+

6 SSTX -

7 GND

8 SSRX+

9 SSRX -

4 Pin Molex Power Anschluss für PC Netzteil- -

DRIVER INSTALLATION

CHECK INSTALLED DRIVER

Open the >Device manager<. Now you should see at „USB-Controller“ the following new entry's:

If you see this or a similar information the device is installed correctly.

Windows 8.x / 10 / 11 / Server 2012R2 & 2016 & 2019 & 2022

After the hardware installation, the operating system will recognize the device automatically and

install the drivers.

CHECK INSTALLED DRIVER

Open the >Device manager<. Now you should see at „USB-Controller“ the following new entry's:

If you see this or a similar information the device is installed correctly.

Linux / Mac

After the hardware installation, the operating system will recognize the device automatically and

install the drivers.

JP1:

Jumper zur Auswahl

der Stromquelle

(Netzteil oder

PCI Express Bus)-

HARDWARE INSTALLATION

DRIVER INSTALLATION

Please note the following installation instructions. Because there are large differences between the

PC’s, we can give you only a general installation instructions for the EX-11092-2. Please refer your

computer s reference manual whenever in doubt.’

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Computer and

gently slide the cover off.

3. Locate an available PCI-Express expansion slot and insert the card. Make sure that the card

is plugged in correctly.

4. If necessary please install now the external power supply to the card.

5. Then attach the card with a screw to the rear panel of the computer.

6. Gently replace your computer s cover and the mounting screws.’

Windows XP / Vista / 7 / Server 2003 & 2008R2

After starting Windows is recognizes a new . Now “ “USB (Universal Serial Bus) Controller-

insert the Driver CD into your CD ROM drive (e.g. drive D:) and start the which is -„ “ setup

located in the folder (see picture):„ “ USB 3.0/RENESAS/uDP720201_202

Follow the installation instructions and complete the installation.

Windows will now install automatically you right driver for your particular operating system. After

the installation the operating system detects the card and automatically install them.

CONNECTORS

4 Pin Molex Power Connector :-

1 +12V 2 GND 3 GND 4 +5V

If JP1 is set to AUX, the connector must be connected to

the power connector from the PC power supply.

Please make sure you connect the plug in the right

direction!

Attention! Never connect or release the plug while the

PC power is on!

INT = (Factory Setting)Power 900mA from PCI Express BUS -

AUX = Power 900mA from PC power supply

(For safe direct power from PC power supply to provide sufficient power

for devices with high power consumption)

The 4 Pin Molex Power Connector must then be connected to the -

PC power supply!

JP1:

INT

AUX

Produktspecifikationer

Varumärke:	EXSYS
Kategori:	nätverkskort/adapter
Modell:	EX-11092-2
Vikt:	400 g
Djup:	65 mm
Höjd:	61 mm
Certifiering:	CE / FCC / WEEE
Värdgränssnitt:	PCIe
Dataöverföringshastighet (max):	5 Gbit/s
Produktens färg:	Silver
Windows-operativsystem som stöds:	Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 8, Windows 8 x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows XP Home, Windows XP Home x64
Temperatur vid drift:	0 - 50 ° C
Temperaturintervall (förvaring):	-20 - 85 ° C
Intervall för relativ operativ luftfuktighet:	5 - 95 %
Hållbarhetscertifiering:	RoHS
Antal USB 3.2 Gen 1 (3.1 Gen 1) typ A-portar:	2
Manual:	Ja
Plug & Play-kompatibel:	Ja
Intern:	Ja
Kretsar:	Renesas uPD720202
Ändamål:	PC
Utgränssnittet:	USB 3.2 Gen 1 (3.1 Gen 1)
Periferiska (Molex) strömkontakter (4-pin):	1
Stöd för hot-plug:	Ja