EXSYS EX-1315IS Bruksanvisning

Läs gratis den bruksanvisning för EXSYS EX-1315IS (2 sidor) i kategorin Annat datortillbehör. Guiden har ansetts hjälpsam av 33 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 7 recensioner. Har du en fråga om EXSYS EX-1315IS eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

6

5

Die EX1315IS USB 3.2 Gen 1 Dockingstation stellt einen seriellen RS232 Port mit -

Überspannungsschutz und Isolation, einen Port mit Ethernet 10/100/1000Mbps sowie zwei USB

3.2 Gen 1 Ports zur Verfügung. Durch die einfache Installation muss der Rechner nicht geöffnet

werden und die EX1315IS kann bei laufendem Betrieb installiert werden.-

Kompatibilität:USB 1.1, 2.0, 3.0, 3.1, 3.2 / TCP/IP 10/100/1000

Betriebssysteme:Win 9.x/ME/2000/XP/Vista/7/8.x/10/11/Server 20xx/Linux/MAC

Anschlüsse:1x USB 3.0 BBuchse, 2x USB 3.0 ABuchse, 1x 9 Pin DSUB Stecker, ---

-- 1x RJ45 Ethernet Anschluss, 1x TBlock 748V, 1x 12V/3A Buchse

Lieferumfang:1315IS, USBKabel, DINRail Kit, Netzteil 12V/3A, AnleitungEX---

1

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

CONNECTORS

CLEANING

DRIVER INSTALLATION

Serial RS-232

After the hardware installation Windows will recognize the device automatically and install the

drivers. If the driver should not be installed automatically, please download the driver from our

homepage (www.exsys.de / www.exsys.ch) first. Now select the folder with your operating

system and install the driver. Follow the hardware assistant and finish the installation.

Important! Restart your PC in any case after installing the drivers.

CHECK INSTALLED DRIVER

Open the . Now you should see at >Device manager<„Ports (COM & LPT)USB“ and „-

Controller “the following new entry:

If you see this or a similar information the device is installed correctly.

To clean the unit, use only a dry, lintfree cloth and apply light pressure to remove dirt. Be -

careful not to leave any fibres of the cloth in the connector area.

Never use a damp or wet cloth for cleaning!

Switzerland:

EXSYS Vertriebs GmbH

Dübendorfstrasse 17

8602 Wangen

www.exsys.ch

Germany:

EXSYS Vertriebs GmbH

Industriestrasse 8

61449 Steinbach

www.exsys.de

Italy:

EXSYS Italia Srl

Via Belvedere, 45/B

I22100 Como -

www.exsys.it

Anleitun

Vers. 1.1 / 22.08.24

E1315I

ANSCHLÜSSE

HARDWAREINSTALLATION

Because there are large differences between PCs, we can give you only a general installation ’

guide for the EX-1315IS. Please refer your computers reference manual whenever in doubt.

1.Connect the EX-1315IS USB to the USB A-Port at the your PC.

2. When you are ready you can start your PC and continue with the Driver Installation.

USB 3.0 BBuchse-

Betriebs LED

9 Pin Seriell RS232 Stecker-

RJ45 Anschluss mit Status LED´s

2 x USB 3.0 ABuchse-

12V/3A DC Buchse

Terminal Block +7V~+48V

Achtung!

Stecker niemals umgekehrt

oder mit Gewalt einstecken.

D-

GND

StdB_SSTX -

StdB_SSTX +

GND_DRAIN

StdB_SSTX+

StdB_SSTX -

D+

VBus

StdB_SSTX -

StdB_SSTX+

GND_DRAIN

VCC

StdB_SSTX +

StdB_SSTX -

D+D-

GND

USB 3.2 BBuchse:-

Attention!

Never plug in with force

or in wrong direction.

USB 3.2 APort:-

RS- 232 Connector:

Serial 9 Pin DSUB Connector-

PinSignalPinSignalPinSignal

14DTR7RTSCDC

2RXD5GROUND8CTS

3TXD6DSR9 RI

RJ45 Connector:

RJ45 Connector

PinSignalPinSignalPinSignal

1BI_DA+4BI_DC+7BI_DD+

2BI_DA5BI_DC8BI_DD- - -

3BI_DB+6BI_DB -

+7V ~ 24V TBlock:-

+7V ~ 24V

GND (Ground)

ATTENTION!!!

Never connect power to GND it will destroy your Hardware!

ATTENTION!!!

Use only with included power supply!

12 Volt Connector:

Ehernet LAN

After the hardware installation Windows will recognize the device automatically and install the

drivers. If the driver should not be installed automatically, please download the driver from our

homepage (www.exsys.de / www.exsys.ch) first. Now select the folder with your operating

system and install the driver. Follow the hardware assistant and finish the installation.

Important! Restart your PC in any case after installing the drivers.

CHECK INSTALLED DRIVER

Open the >Device manager<Ethernet Adapter. Now you should see at „“ the following new

entry:

If you see this or a similar information the device is installed correctly.

USB 3.2

After the hardware installation, the OS will recognize the device automatically and install the

drivers

CHECK INSTALLED DRIVER

Open the . Now you should see at >Device manager<„USB Devices“ the following new entry:

<Generic USB Hub>.

Produktspecifikationer