GE 15136 Bruksanvisning

GE Tidsbrytare 15136

Läs gratis den bruksanvisning för GE 15136 (3 sidor) i kategorin Tidsbrytare. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 8.5 recensioner. Har du en fråga om GE 15136 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

APPLICATION

This digital GE Time Switch (15132) is a universal, electromechanical time

switch which can be ﬁeld conﬁgured for various power supply voltages.

The voltage options include 120VAC, 208/240VAC and 277VAC – all within

the same unit! Selection of the desired supply voltage is easily achieved

by positioning dipswitches on the printed circuit board assembly (consult

Dipswitches Conﬁguration on back). The mechanism is mounted in a NEMA

indoor or outdoor enclosure and is intended for the control of lighting, heating,

air conditioning, pumps, motors, or general electrical circuits in residential,

commercial, industrial and agricultural facilities.

SPECIFICATIONS

Input Voltage: 120 VAC, 208/240 VAC, or 277 VAC in all units based

upon dipswitch conﬁguration.

15087 NEMA 3R Indoor & Outdoor BM-A301US5-O2

15207 NEMA 1 Indoor BM-A301US5-I2

56922 NEMA 1 Indoor BM-A301US5-I2

15132 NEMA 3R Indoor & Outdoor EM-A301US9-O2

Switch Rating: DPDT Models

Normally Open Contacts

40A Resistive, 120-277Vac.

30A General Purpose, 120-277Vac.

20A Resistive, 30Vdc

1 HP, 120Vac ; 2HP, 240Vac ;

20A Ballast, 120-277Vac.

15A Tungsten, 120Vac

5.4A Tungsten, 208-277Vac.

800VA, Pilot Duty, 120Vac.

720VA, Pilot Duty, 240-277Vac.

TV-5, 120Vac

Normally Closed Contacts

30A Resistive, 120-277Vac

15A General Purpose, 120-277Vac

15A Resistive, 30Vdc

20A Ballast, 120-277Vac

1/4HP, 120Vac; 1/2HP, 208-240Vac.

290VA, Pilot, 120Vac.

360VA, Pilot, 208-240Vac.

NOTE: If loads are connected to both NC and NO contacts, both contacts are

decorated to 67% of the above values.

ENVIRONMENTAL RATINGS

Ambient Temperature: –40F to 130F

Humidity: 0-95% RH, Non-condensing

WIRING CONNECTIONS

Screw clamp terminals for up to 2 AWG #8 wires per position. For supply

connections, use 8AWG or larger wires suitable for at least 105° C. Use copper

conductors only.

Lights

Power LED (Orange) – Light illuminates when power is applied to

the timer

Status LED (Green) – Light illuminates when power is applied to load.

Included Hardware

INSTALLATION

CAUTION: Before wiring or servicing, power to this time switch and the

equipment it controls must be turned off. Turning off the time switch only

will not prevent a shock hazard. Replace cover plate within housing before

supplying power to time switch. If you are not comfortable installing this

device please contact a licensed electrician. Before installing this product read

all instructions carefully.

Removing Knockout

1. Select knockouts to be used. Remove the inner 1/2” knockout by inserting

a ﬂathead screwdriver on the inner most ring and carefully punching the

knockout loose. Remove slug. If the 3/4” knockout is required, remove the

outer ring with pliers after removing the 1/2” knockout. Smooth edges with

a knife if necessary.

Please refer to Quick Start Guide for Examples and More Details.

Mounting of the Time Switch Box

NOTE - Before mounting be sure to remove knockouts for the wires, (see Quick

Start Guide)

1. In order to mount the box you will need the 3 supplied anchors and 3

supplied screws from the hardware list above. (Anchors included are

designed for mounting on sheetrock.)

2. Using the box as a template, mark with a pencil where the three pilot holes

will be drilled.

3. Using the appropriate drill bit size, drill the pilot holes (Note that if drilling

into wood or metal a specialized drill bit may be needed.)

See Drill Diagram.

4. For sheetrock; use a hammer to gently tap the anchors into the pilot holes.

5. Place the box up to the pilot holes or anchors and insert the screws

accordingly.

Wiring the Device to the Timer

NOTE - For outdoor installation use rain tight or wet location conduit hubs that

comply with requirements of UL 514B (standard for ﬁttings for conduit and

outlet boxes).

1. Remove 2 screws retaining the interior cover panel and remove the panel.

2. Refer to Figure 1 and wiring diagrams to determine appropriate placement

of wires. It is the responsibility of the installer to ensure that all applicable

National and Local code requirements are met. If you are unsure of these

requirements, contact a licensed electrician immediately.

3. GROUNDING: This enclosure is of plastic construction and does not require

a ground connection. This enclosure does not provide grounding between

Digital Time Switch

Soft Wood 5/64”

Material Drill Bit Size

Drill Diagram

Hard Wood 3/32”

Metal 5/64”

Sheetrock 3/16”

Anchors Needed?

Yes

QTY Hardware

3 M4 Anchors 1” Long

3 M4 Screws 1” Long

2 8 AWG Jumpers for 240V AC

2 10 AWG Jumpers for 120V AC

1 Wire Nut (For Ground Wires)

15136 NEMA 3R Indoor & Outdoor

GE 15136 Timer

http://waterheatertimer.org/GE-timers-and-manuals.html#15136

Produktspecifikationer

Varumärke:	GE
Kategori:	Tidsbrytare
Modell:	15136
Färg på produkten:	Wit
Vikt:	280 g
Snäll:	CCTV-bewakingscamera
Husmaterial:	Kunststof
Internationell säkerhetskod (IP):	IP66
Blåtand:	Nee
Vormfaktor:	Rond
Placeringsstöd:	Binnen & buiten
Anslutningsteknik:	Bedraad
Ethernet LAN:	Nee
Monteringsmetod:	Muur
Totalt antal megapixlar:	1 MP
Typ av strömkälla:	DC
Minimal belysning:	0 Lux
Antal kameror:	1
Inbyggd hårddisk:	Nee
Nattseende:	Ja
LED-typ:	IR
Fast brännvidd:	3.6 mm
Strömförbrukning (max):	5 W
Analog signalformat:	NTSC, PAL
Optisk sensorstorlek:	1/4 "
Bildsensortyp:	CMOS
Förvaringstemperatur:	-20 - 40 °C
Säkerhetsfunktioner:	Waterbestendig
Spännande:	12 V
Signal-brusförhållande:	41 dB
PTZ-kontroll:	Ja
Night vision scope:	30 m
Antal LED-belysning:	36
Bakgrundsljuskompensation:	Ja
Antal effektiva pixlar (H x V):	1920 x 1080 Pixels
Wifi:	Nee
Drifttemperatur (TT):	-20 - 60 °C