GT 614 Bruksanvisning
Läs gratis den bruksanvisning för GT 614 (4 sidor) i kategorin Billarm. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 6.5 recensioner. Har du en fråga om GT 614 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
1
GT613UKRev02.p65
GT613 - 614 - 615 FITTING INSTRUCTIONS
GREY/BLACK
BATTERY
IGNITION KEY
RED
YELLOW/BLACK (RELAY OUTPUT)
+15/54
IGNITION SWITCHED LIVE
YELLOW
CUT
15 AMP FUSE
BROWN
EARTH
VEHICLE
RED/GREY
PINK
GREEN/BLACK
GREEN
GREEN/BROWN
ORANGE
Positive output when the
Additional sensors/modules
To the GREEN/BLACK wire
NEGATIVE command for the starter
PIN SWITCH
BOOT/BONNET ORIGINAL DOOR
PINSWITCH
Connect to either near side or
off side indicator wire
Constant or intermittent output when the alarm is
being triggered (current max. 5A). With this wire it
is possible to drive the HORN relay, an electronic
siren (GT43) the parking lights or a after market satellite
system.
CONTROL UNIT
Connect to positive or negative depending on the
polarity required on the YELLOW/BLACK wire.
immobilisation (current max 80mA)
Additional relay 85
86
87
87A
30
M
Diode 1N4007
+15/54
* NOTE: it is possible to use the GT465 module
RED
BLACK
BLACK (RELAY COMMON)
CHECK LED
+12V
GT431
-+
BROWN
PINK
GREEN/BLACK
GT632GT431
alarm is armed
(current max. 80mA)
on additional sensors/modules
+12V
STARTER MOTOR*
Tilt sensor adjustment
clockwise = more sensitive
anti-clockwise = less sensitive
(use the supplied screwdriver)
WHITE RED
or satellite system
INDICATORS
IMMOBILISATION
CORRECT
ABOVE THE DASHBOARD INCORRECT POSITIONS
CENTRE
DASHBOARD
POSITIONS CONSOLE
RED
WHITE
POSITIONING OF THE
GT431 ULTRASONIC SENSORS POSITIONING OF THE GT 632
HYPERFREQUENCY SENSOR
WARNING: Incorrect installation will
increase the risk of water ingress
into the siren.
Make sure that the loom cover is
attached with supplied screws and
the sheath covers the neck of the
loom cover and secured with a cable
tie.
TRANSMITTING
SIDE
LED
ADJUSTMENT
TRIMMER
ADJUSTMENT
GT431
-+
SENSITIVITY
ADJUSTMENT
It is advisable to place the alarm as
indicated in the figure to obtain the
maximum of performances by the
shock sensor. Note that the maximum
sensitivity is obtained with a 30°
angulation.
Correct alarm positioning for the shock sensor
SHOCK SENSOR
MINIMUM SENSITIVITY
SHOCK SENSOR M
AXIMUM SENSIITIVITY
70 degrees
30 degrees
Produktspecifikationer
| Varumärke: | GT |
| Kategori: | Billarm |
| Modell: | 614 |
Behöver du hjälp?
Om du behöver hjälp med GT 614 ställ en fråga nedan och andra användare kommer att svara dig
Billarm GT Manualer
10 September 2024
8 September 2024
5 September 2024
4 September 2024
2 September 2024
1 September 2024
30 Augusti 2024
29 Augusti 2024
28 Augusti 2024
24 Augusti 2024
Billarm Manualer
Nyaste Billarm Manualer
5 September 2025
4 September 2025
4 September 2025
4 September 2025
20 Juni 2025
9 April 2025
23 September 2024
21 September 2024
18 September 2024
18 September 2024