Hifonics Brutus Elite BE40-1500.2D Bruksanvisning
Sidor 2 Engels mottagare
Läs bruksanvisningen för Hifonics Brutus Elite BE40-1500.2D gratis online eller ladda ner PDF:en. 19 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
5
7
6
8
11
12
4
High Level Input
- DC turn on
- Music Sense
Low Level Input
- REM turn on
(Remote wire turn on)
Please scan QR code below or go to
Hifonics.com/product-manuals for the
Auto-Sense Technical Guide.
Turn on Mode
9
Model Fuse Size Cable Size
4ga
0ga
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock single woofermultiple woofersMonoblock
Bridged
10
MUSIC SENSE
DC SENSE
REMOTE
TURN ON MODE
NOTE - When using low level input and the RCA’s are plugged into the amplier and the TURN ON
MODE is in the DC ON position, the amplier will NOT turn on. Please re-read QR document above
or hire a professional installer.
BE40-1000.1D
BE40-1500.1D
BE40-2000.1D
BE40-3000.1D
BE40-1500.2D
BE40-1500.4D
BE40-2000.5D
2x60A
External 150A
External 200A
External 300A
External 150A
External 150A
External 200A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Disconnect
Negative Battery
Terminal
Run Cables
Mount Amplier
Installation
1
2
3
CH1 CH2
CH1 CH2
Common System Setup
4ch - Full Range
4ch - Mixed Mono
Mono
5ch
CH1 CH2
2ch - Full Range
Produktspecifikationer
| Varumärke: | Hifonics |
| Kategori: | mottagare |
| Modell: | Brutus Elite BE40-1500.2D |
| Färg på produkten: | Grijs |
| Vikt: | 600 g |
| Bredd: | 105 mm |
| Djup: | 140 mm |
| Höjd: | 65 mm |
| Användarmanual: | Ja |
| Internationell säkerhetskod (IP): | IP67 |
| Placeringsstöd: | Buiten |
| Anslutningsteknik: | Bedraad |
| Ethernet LAN: | Nee |
| Monteringsmetod: | Plafond |
| Maximal upplösning: | 768 x 494 Pixels |
| Strömutgång (volt): | +12V |
| Minimal belysning: | 0.4 Lux |
| Medföljande kablar: | BNC |
| Nattseende: | Ja |
| LED-typ: | IR |
| Infraröd våglängd: | 850 nm |
| Brännvidd: | 3.6 - 8 mm |
| Analog signalformat: | NTSC, PAL |
| Optisk sensorstorlek: | 1/3 " |
| Anslutning för nätadapter: | Ja |
| Bildsensortyp: | CCD |
| Optisk zoom: | - x |
| Kamerans slutartid: | 1/100000 s |
| Gränssnitt: | BNC |
| vitbalans: | Auto |
| Max 30 bilder per sekund: | 60 fps |
| Signal-brusförhållande: | 48 dB |
| Antal TV-linjer: | 520 |
| Dag/nattläge: | Ja |
| Antal LED-belysning: | 40 |
| Strömförbrukning (typiskt): | 8.4 W |
| Drifttemperatur (TT): | -40 - 60 °C |
| F-nummer (relativ bländare): | 1.2 |
| NTSC-upplösningar: | 768 x 494 Pixels |
| PAL-upplösningar: | 752 x 582 Pixels |
| Infraröda lysdioder är levande: | 20000 uur |
Behöver du hjälp?
Om du behöver hjälp med Hifonics Brutus Elite BE40-1500.2D ställ en fråga nedan och andra användare kommer att svara dig
mottagare Hifonics Manualer
Hifonics ZEUS ZTH-2225.1D Bruksanvisning Hifonics ZEUS ZG-1800.1D Bruksanvisning Hifonics ZEUS ZD-2550.1D Bruksanvisning Hifonics ALPHA A1200.4D Bruksanvisning Hifonics TSi600-II Bruksanvisning Hifonics Brutus Elite BE40-2000.1D Bruksanvisning Hifonics Brutus BRX12000D Bruksanvisning Hifonics MT Olympus Bruksanvisning
Alla Hifonics mottagare manualer
Populära i mottagare
Hifonics NXi4002 Bruksanvisning Hifonics HAC-3000.1D Bruksanvisning Hifonics Pluto II Bruksanvisning
mottagare Manualer
Nyaste mottagare Manualer
Shure MXN-AMP Bruksanvisning Wavtech Link750.1plus Bruksanvisning ETON Stealth 7.1 DSP Bruksanvisning Ashly FX-500.8 Bruksanvisning Ashly FX-750.8 Bruksanvisning OWI AMPMA70V40 Bruksanvisning Alpine PXE-X121-12EV Bruksanvisning Boss Elite BE7ACP.WXC Bruksanvisning LEA Connect CS704 Bruksanvisning Citronic QP1600 Bruksanvisning