Honeywell IS3050 Bruksanvisning
Honeywell
Rörelsedetektorer
IS3050
Läs gratis den bruksanvisning för Honeywell IS3050 (4 sidor) i kategorin Rörelsedetektorer. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 2 recensioner. Har du en fråga om Honeywell IS3050 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
IS3050 Passive Infrared Motion Sensor - Installation Instructions
QUICK LINKS
Mounting Location Guidelines
Open the Sensor
Mount the Sensor
Sensor Co nts and Settingsmpone
Wire the Sensor
Walk Test the Sensor
Detection Patterns
Relay Operation
Troubleshooting
Sensor Specifications
Accessories
Approval Listings
Mounting location guidelines:
• The optimal range is obtained at a
mounting height o f 7’ 6” (2.3 m).
• - - Allow a clear line of sight to all areas to protect.
• Do not directly face windows.
• . Avoid close proximity to moving machinery, fluorescent lights, and heating/cooling sources
• Not for use in applications with pets.
1. Turn the arrow to point to the Unlock symbol.
2. Press firmly on housing latch.
3. Gently separate the front and rear housing.
- 2 -
• [A] = Wall mounting holes.
• [B] = Corner mounting holes.
• The rear tamper plate MUST
be mounted to a stud, solid
wood, or with a robust wall
anchor.
- 3 -
LED
Power
Up Walk Test Normal Trouble
Red
Slow
Blink
ON
Alarm
ON
Alarm
Fast
Blink
Zones
A
2 Look-down
B
18
Lower
C
20
Intermediate
D
54
Long
1. Close the sensor and apply power to the sensor. Initialization is complete when the LED stops flashing
slowly (about 0 seconds).2
2. Walk through the detection area and observe the LED.
Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters
normal operation mode. For an additional 10 minute walk test, enable est mode again with the w talk
f . lashlight feature
Note: During power up and w est mode the LED is active regardless of the LED Enable/Disable Dip switch setalk t s ting.
Flashlight Feature:
1. Use a flashlight with a bright light beam, and stand within 4’ (1.2 m) of the sensor.
2. Swing the light beam past the sensor IR window 3 5 times, holding the beam -
on the window for 0.5 second each pass.
The flashlight feature is only available for the first 24 hours after first power up .
Produktspecifikationer
| Varumärke: | Honeywell |
| Kategori: | Rörelsedetektorer |
| Modell: | IS3050 |
Behöver du hjälp?
Om du behöver hjälp med Honeywell IS3050 ställ en fråga nedan och andra användare kommer att svara dig
Rörelsedetektorer Honeywell Manualer
27 Juli 2024
Rörelsedetektorer Manualer
- Brennenstuhl
- Black Box
- Bticino
- Silvercrest
- EVE
- Konig
- Blaupunkt
- Steinel
- DSC
- Smartwares
- Renkforce
- Arlo
- Vemer
- Alecto
- Hama
Nyaste Rörelsedetektorer Manualer
9 Januari 2025
10 Oktober 2024
6 Oktober 2024
4 Oktober 2024
3 Oktober 2024
30 September 2024
27 September 2024
24 September 2024
22 September 2024
17 September 2024