ISDT UC1 Bruksanvisning

ISDT Batteriladdare UC1

Läs gratis den bruksanvisning för ISDT UC1 (3 sidor) i kategorin Batteriladdare. Guiden har ansetts hjälpsam av 20 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 10.5 recensioner. Har du en fråga om ISDT UC1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

Please read this user manual in detail and follow the instructions carefully before

using your new charger：

1.Keep the charger away from humidity and heat source while charging, ensure

proper cooling during use.

2.Make sure the battery cells is correct before charging, avoid over-discharge of

the battery.

3.This charger can only use for 2~6S Lipo (voltage 7.4~26V) battery as power

supply. Do not use an input power supply beyond the range of voltage, avoid

damage the charger or even cause dangerous.

Attention

Operation button

Indicator light

XT60 power input port

USB output port

UC1 Smart Charger Instructions

Speciﬁcations

Type: UC1

Power input port: XT60

Input voltage: 2~6S LiPo (7.4~26V)

Max output current: 2A

Max output power: 18W

Charging protocol support:

QC2.0/3.0, FCP, BC 1.2

Operating temperature: 0 ~40 ℃

Size: (L × W × H) 48.5×22×14.5mm

Weight: 23 g

Indicator light status

Indicator

light

Instructions

Output

Solid green

light

Red light

quick ﬂash

Red light

slow ﬂash

Purple light

slow ﬂash

Cyan light

slow ﬂash

Charging

Internal circuit

abnormal,

charging stop

Low voltage

alarm,

the ﬂash times

is the number

of battery cells

The input

voltage is

higher than

the battery

cells setting

Setting

state

Operating instructions

*All pictures, statements and text information of this product are for reference only.

Please refer to the actual information on the oﬃcial website www.isdt.co.

SHENZHEN ISD TECHNOLOGY CO.,LTD reserves the right for ﬁnal explanation and modiﬁcation of the speciﬁcation.

1. Plug the 2~6S Lipo battery with XT60 to input port, the indicator light turns

green means normal state. If the cell amounts setting on UC1 is not match the

battery cells, the indicator light turns purple or red at slow ﬂash.

2. Press and hold the button for 3 seconds until the light turns cyan, it enters the

setup state to set the battery cells.

3. The cyan light ﬂash times is the battery cells that have been set. Press the

button to alter the battery cells within 2~6S running in cycle. When the

cyan-light ﬂash times are same as battery cells, press and hold the button

more than 3 seconds and it will save the setting and exit.

4. Press button can check the battery cells during charging. The ﬂash times

of the green light is the battery cells.

5. When the red light ﬂash slowly it indicates low battery capacity, you should

cut oﬀ to prevent the over-discharge, otherwise, it will consume current internal.

Produktspecifikationer

Varumärke:	ISDT
Kategori:	Batteriladdare
Modell:	UC1
Vikt:	23 g
Bredd:	22 mm
Djup:	14.4 mm
Höjd:	48.5 mm
Uteffekt:	2 A
Spänning:	7.4 - 26 V
Produktens färg:	Grå
Antal USB-portar:	1
Antal per förpackning:	1 styck
Utgångsspänning:	5 - 12 V
Strömkälla av typen:	DC
Batterier medföljer:	Nej