Jonsbo CR-1000 GT Bruksanvisning


Läs gratis den bruksanvisning för Jonsbo CR-1000 GT (2 sidor) i kategorin kylsystem för dator. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 2 recensioner. Har du en fråga om Jonsbo CR-1000 GT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
Thermal Grease
Intel Bracket
AMD Bracket
B
C
D
E
F
Step1
Step2
Step3
Step4
Step5
Step6
Step7
根据主板型号将支架上的螺杆移到对应位置。
(如上图所示)
Move the screw on the bracket to the corresponding position
according to the main board type.
(As shown in the above figure)
将散热膏均匀涂抺在CPU表面上,并取下散热器
底部的保护膜。
Evenly spread the heat sink paste on the surface of the CPU and
remove the bottom of the radiator.
将背板定位滑块移至所需位置后,装入主板。
(如上图所示)
The backplane positioning slider is moved to the desired position
and loaded into the main board.
(As shown in the above figure)
将散热器置于CPU上,同时将支架螺杆对准
背板螺母并拧紧。(如上图)
Place the radiator on the CPU while aligning the support
screw to the backplane nut and tightening
Pictured above
装上风扇。
Install the fan.
Connect the power cord to the system board.
(pictured above)
将电源线与主板连接。(如上图)
安装散热器前先移除风扇,用手掰开箭头指示的2个
卡扣可移除风扇。
LGA115X
AM4
AM3+/AM3/AM2+/AM2/
FM2+/FM2/FM1
Step7
Step6
Step1
Step2
Step3
Step4
Step5
Step8
请将AMD主板上的原厂散热支架移除。(如上图)
Please remove the original heat sink bracket on the
AMD motherboard.
Pictured above
将散热膏均匀涂抺在CPU表面上,并取下散热器
底部的保护膜。
Evenly spread the heat sink paste on the surface of the
CPU and remove the bottom of the radiator.
根据主板型号将支架上的螺杆移到对应位置。
(如上图所示)
Move the screw on the bracket to the corresponding position
according to the main board type.
(As shown in the above figure)
将散热器置于CPU上,同时将支架螺杆对准
主板原装散热架底座孔位并拧紧。(如上图)
Pictured above
Place the radiator on the CPU and screw the bracket screw
to the base of the original cooling rack
装上风扇。
Install the fan.
CR-1000
将电源线与主板连接。(如上图)
Connect the power cord to the system board.
(pictured above)
安装散热器前先移除风扇,用手掰开箭头指示的2个
卡扣可移除风扇。


Produktspecifikationer

Varumärke: Jonsbo
Kategori: kylsystem för dator
Modell: CR-1000 GT
Vikt: 610 g
Bredd: 76 mm
Djup: 128 mm
Höjd: 158 mm
Ljudnivå (låg hastighet): 20.55 dB
Modell: Kylare
Minsta luftflöde: 26.1 cfm
Maximalt luftflöde: 66.81 cfm
Rotationshastighet (max): 1800 RPM
Antal skruvar: 4
Rotationshastighet (min): 700 RPM
Spänning: 12 V
Antal fläktblad: 9
Antal värmerör: 4
Produktens färg: Svart
Monteringssats: Ja
Antal per förpackning: 1 styck
Fläktdiameter: 120 mm
Belysningsfärg: Multi
Antal fläktar: 1 fläkt/-ar
Skruvar medföljer: Ja
LED-belysning: Ja
Ljudnivå (hög hastighet): 37.2 dB
Lämplig placering: Processor
Stödd processor uttag: LGA 1150 (Socket H3), LGA 1151 (Socket H4), LGA 1155 (Socket H2), LGA 1156 (Socket H), LGA 775 (Socket T), Socket AM2, Socket AM2+, Socket AM3, Socket AM3+, Socket AM4, Socket FM1, Socket FM2, Socket FM2+
Stöd för pulsbreddsmodulering (PWM): Ja
Mått, fläkt (B x D x H): 120 x 120 x 25 mm
Fan kontakt: 4-stift
Termisk platta inkluderad: Ja

Behöver du hjälp?

Om du behöver hjälp med Jonsbo CR-1000 GT ställ en fråga nedan och andra användare kommer att svara dig