Joy-it SBC-MotoDriver3 Bruksanvisning
Joy-it
Inte kategoriserad
SBC-MotoDriver3
Läs gratis den bruksanvisning för Joy-it SBC-MotoDriver3 (17 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 5.5 recensioner. Har du en fråga om Joy-it SBC-MotoDriver3 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/17
Joy-IT powered by SIMAC Electronics GmbH - Pascalstr. 8 - 47506 Neukirchen-Vluyn - www.joy-it.net
SBC-MOTODRIVER3
Motor driver board for DC and stepper motors
TABLE OF CONTENTS
1. General information
3. Changing the I
2
C address
4. Pin assignment
5. Use with Raspberry Pi
4.1 Connection
4.2 Installation
4.3 Use of stepper motors
5. Use with Raspberry Pi Pico
5.1 Connection
5.2 Installation
5.3 Code example
5.4 Use of stepper motors
6. Use with ARD-ONE-C (Arduino compatible)
6.1 Connection
6.2 Installation
6.3 Code example
6.4 Use of stepper motors
7. Use with micro:bit
7.1 Connection
7.2 Installation
7.3 Code example
7.4 Use of stepper motors
7.5 Pairing the micro:bit
8. Additional information
9. Support
1. GENERAL INFORMATION
Dear Customer,
thank you for choosing our product. In the following, we will show you
what you should pay attention to during commissioning and use.
Should you encounter any unexpected problems during use, please feel
free to contact us.
With the MotoDriver3 you have the possibility to control and power up to
four DC motors or two stepper motors. The connected motors are
controlled via the PCA9634 chip, which provides an I2C interface.
This motor driver board can be configured to 128 possible I2C addresses.
These can be chosen freely, but in the further course the default address
0x15 is used.
In the following figure you can see which resistors can be changed to
change the I2C address of the motor driver board. You can re-solder these
resistors from A1 up to A7 between GND and VDD to get dierent I2C
addresses.
Here the positions of the seven resistors can be translated to a 7-bit
binary value. Here we take the standard address of the motor driver
board
0x15
which can be translated to
001 0101b
:
A1 = 1 | A2 = 0 | A3 = 1 | A4 = 0 | A5 = 1 | A6 = 0 | A7 = 0
It should be noted that one should never change the I2C address
during operation as this can lead to unpredictable problems.
2. CHANGING THE I2C ADDRESS
Produktspecifikationer
| Varumärke: | Joy-it |
| Kategori: | Inte kategoriserad |
| Modell: | SBC-MotoDriver3 |
Behöver du hjälp?
Om du behöver hjälp med Joy-it SBC-MotoDriver3 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Joy-it Manualer
8 April 2025
8 April 2025
31 Januari 2025
29 Januari 2025
29 Januari 2025
15 Januari 2025
2 Januari 2025
28 December 2024
5 December 2024
5 December 2024
Inte kategoriserad Manualer
- Creative
- Pengo
- SoundLAB
- Dahle
- Harley Benton
- Cambo
- Ruggard
- NutriBullet
- Ventev
- Contax
- Premier Mounts
- Metra
- Renegade
- GAMO
- Goliath
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025