Kern HBA 100-0 Bruksanvisning
Läs gratis den bruksanvisning för Kern HBA 100-0 (7 sidor) i kategorin mätning. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 2.5 recensioner. Har du en fråga om Kern HBA 100-0 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction manual analog shore
hardness tester
SAUTER (&TI) HB
Version 2.0
03/2020
GB
HB- -e-2020 BA
PROFESSIONAL MEASURING
2 - -e-2020 HB BA
GB
SAUTER HB (&TI)
V. 2.0 03/2020
Instruction manual analog shore hardness tester
Thank you for purchasing the analogue Shore hardness tester from SAUTER. We
hope you will be very satised with the high quality of the hardness tester and its
functionality. For any questions, wishes and suggestions we are at your disposal.
Table of contents:
1 Before commissioning .................................................................................. 3
2 General overview ........................................................................................... 3
3 Technical data ................................................................................................ 4
4 Measurement method .................................................................................... 4
5 Storage ........................................................................................................... 4
6 SHORE DUROMETER TEST STAND with HB .............................................. 5
7 Introduction .................................................................................................... 5
8 Structure ......................................................................................................... 5
9 Operation ........................................................................................................ 6
10 Note ................................................................................................................. 7
11 Maintenance ................................................................................................... 7
HB- -e-2020 3 BA
1 Before commissioning
Before putting the device into operation, check the delivery for any transport damage
to the packaging, the plastic case and the device itself. Should this be the case,
SAUTER must be contacted immediately.
2 General overview
The hardness of plastic is generally measured with a Shore hardness tester, using
either the or the scale. This is the preferred method for rubber or Shore A Shore D
elastomers and also for "softer" plastics such as polyolens, uoropolymers and vinyl.
The Shore A scale is used for "softer" rubbers and the Shore D scale for the "harder"
rubbers.
Shore C/ Shore 0 is mainly used for tests with foam rubber, sponges, microporous
plastic, etc.
These three dierent tips (see gure above) are not interchangeable. For each
hardness range the corresponding Shore hardness tester must be purchased.
Developed according to the following standards:
• DIN 53505
• ASTM D2240
• ISO 868
This Shore hardness tester is especially recommended for internal comparison
measurements. Standard calibrations, e.g. to DIN 53505, are often not possible due to
very tightly specied standard tolerances and are therefore not oered by SAUTER.
Shore A, Shore C / Shore 0 and Shore D
Produktspecifikationer
| Varumärke: | Kern |
| Kategori: | mätning |
| Modell: | HBA 100-0 |
Behöver du hjälp?
Om du behöver hjälp med Kern HBA 100-0 ställ en fråga nedan och andra användare kommer att svara dig
mätning Kern Manualer
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
mätning Manualer
- Eastron
- Emko
- Hager
- Uni-T
- PeakTech
- Blackmagic Design
- Basetech
- Owon
- Fluke
- Greisinger
- Gossen Metrawatt
- Yato
- Chauvin Arnoux
- Megger
- Milwaukee
Nyaste mätning Manualer
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025