Kicker KXMA1200.1 Bruksanvisning

Kicker mottagare KXMA1200.1

Läs gratis den bruksanvisning för Kicker KXMA1200.1 (14 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om Kicker KXMA1200.1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/14

KXMA1200.1

Manual del Propietario | Español

AMPLIFICADOR DEL LA SERIE KXM.1

Benutzerhandbuch | Deutsch

MONOVERSTÄRKER DER KXM.1-SERIE

Manuel d’utilisation | Française

AMPLIFICATEUR DE SÉRIE KXM.1

KXM

AMPLIFIERS

Owner’s Manual

KXM.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a dry, structurally sound location to mount your KICKER ampliﬁ er. Make sure there

are no items behind the area where the screws will be driven. Choose a location that allows at least 4”

(10cm) of open ventilation for the ampliﬁ er. Drill four holes using a 7/64” (3mm) bit and use the supplied

#8 screws to mount the ampliﬁ er.

Wiring: The KXM ampliﬁ er’s RCA inputs will receive either high or low level signals from your car stereo’s

source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA

input on the end panel of the ampliﬁ er using the KICKER KISL as shown. Alternatively, the signal can be

delivered to the ampliﬁ er using the low-level RCA outputs on the source unit. Keep the audio signal cable

away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a

90 degree angle.

PERFORMANCE

MODEL: KXMA1200.1

IMPORTANT SAFETY WARNING

PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED

OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE

AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO

4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)

CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.

NOTE: 2017 KXM ampliﬁ er subwoofer channels are 1Ω stable - power rating equivalent to 2Ω operation, +/- 10%

Model: KXMA1200.1

RMS Power

@ 14.4V, 4Ω mono, ≤ 1% THD+N

@ 14.4V, 2Ω mono, ≤ 1% THD+N

600W x 1

1200W x 1

Length [in, cm] 9-9/16,24.4

Height [in, cm] 2 1/8, 5.5

Width [in, cm] 8 5/16, 21

Frequency Response ± 1dB 10Hz–160Hz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity 250mV–10V

Selectable Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave

KickEQ+™ Parametric Bass Boost Boost - Variable 0–18db; Center Frequency - 20Hz–80Hz; Bandwidth 1–5

Subsonic Filter Variable 10–80Hz, 24dB/octave

Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampliﬁ er.

source unit

high-level speaker

outputs

to ampliﬁ er

shield

–

core conductor KICKER KISL (optional)

from source unit high-

level speaker outputs

to ampliﬁ er

Model External Fuse

(sold separately)

Power/Ground Wire KICKER Wiring Kit

KXMA1200.11 x 150 Ampere 4 Gauge PK4, CK4

12V

RADIO

DETECT

battery

external fuse

remote turn-on (see page 5)

woofer

MONO OPERATION

minimum impedance of 1 ohm

ABYC-compliant power terminals

Ampliﬁ er uses 304-stainless steel screws

and conformal coated PCB for increased

weather resistance

aluminum bottom plate

≤7”

(18cm)

Produktspecifikationer

Varumärke:	Kicker
Kategori:	mottagare
Modell:	KXMA1200.1
Färg på produkten:	Black, Orange
Vikt:	1678.3 g
Ljudnivå:	66 dB
Tillgångar:	- W
Batteri/Batterispänning:	20 V
Inkluderar batteriladdare:	Ja
Luchtsnelheid:	0.12 km/h
Batteriteknik:	Lithium-Ion (Li-Ion)
Driftsteknik:	Electrisch
Operationstyp:	Blazen