Kicker KXMA400.4 Bruksanvisning

Kicker mottagare KXMA400.4

Läs gratis den bruksanvisning för Kicker KXMA400.4 (11 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 1.5 recensioner. Har du en fråga om Kicker KXMA400.4 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/11

KXMA400.2 | KXMA1200.2

KXMA400.4

Manual del Propietario | Español

AMPLIFICADOR DEL LA SERIE KXM.2

Benutzerhandbuch | Deutsch

STEREOVERSTÄRKER DER KXM.2-SERIE

Manuel d’utilisation | Française

AMPLIFICATEUR DE SÉRIE KXM.2

KXM

AMPLIFIERS

Owner’s Manual

KXM STEREO-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no

items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm)

of open ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger

compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the

ampliﬁ er.

Wiring: The KXM ampliﬁ er’s RCA inputs will receive either high or low level signals from your car stereo’s

source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA

input on the end panel of the ampliﬁ er using the KICKER KISL as shown. Alternatively, the signal can be

delivered to the ampliﬁ er using the low-level RCA outputs on the source unit. Keep the audio signal cable

away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a

90 degree angle.

PERFORMANCE

MODEL: KXMA400.2 | KXMA1200.2 | KXMA400.4

IMPORTANT SAFETY WARNING

PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER

IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO

SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS

DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4

INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT

LEAST 1 INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY

SURFACE.

Model: KXMA400.2 KXMA1200.2 KXMA400.4

RMS Power

@ 14.4V, 4 stereo, ≤ 1% THD+N

@ 14.4V, 2 stereo, ≤ 1% THD+N

@ 14.4V, 4Ω mono, ≤ 1% THD+N

100 x 2

200 x 2

400 x 1

300 x 2

600 x 2

N/A

50 x 4

100 x 4

200 x 2

Length [in, cm] 9-9/16, 24.4 11-3/16, 28.4 11-3/16, 28.4

Speciﬁ cations common to all models:

Height [in, cm] 2-1/8, 5.5

Width [in, cm] 8-5/16, 21

Frequency Response [Hz] 10Hz–20kHz

Signal-to-Noise Ratio [dB] 95dB

Input Sensitivity 250mV–10V

Selectable Electronic Crossover Off; Variable HP, 10–500Hz; Variable LP, 40–500Hz; 400Hz–5,000Hz

with 10X Switch (bandpass capable); Slope: 24dB/octave"

KickEQ™ Bass Boost 0–18dB @ 40Hz

Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampliﬁ er.

POWER WIRING

source unit

high-level speaker

outputs

to ampliﬁ er

shield

–

core conductor KICKER KISL (optional)

from source unit high-

level speaker outputs

to ampliﬁ er

Model External Fuse

(sold separately)

Power/Ground Wire KICKER Wiring Kit

KXMA400.2 1 x 60 Ampere 8 Gauge PK8, CK8

KXMA1200.2 1 x 150 Ampere 4 Gauge PK4, CK4

KXMA400.4 1 x 100 Ampere 4 Gauge PK4, CK4

RADIO

DETECT

12V

battery

external fuse

remote turn-on (see page 6)

≤7”

(18cm)

ABYC-compliant power terminals

Ampliﬁ er uses 304-stainless steel screws

and conformal coated PCB for increased

weather resistance

aluminum bottom plate

Produktspecifikationer

Varumärke:	Kicker
Kategori:	mottagare
Modell:	KXMA400.4
Beeldscherm:	FSTN LCD
Skärm diagonal:	4 "
Vattentät:	Ja
Genomsnittlig effekt:	125 W
Antal batterier/batterier som stöds:	6
Bakgrundsbelysning:	Ja
Frekvens:	200 kHz
Mått (B x D x H):	107.2 x 69.09 x 146.3 mm
Toppeffekt:	1000 W
Batterityp:	AA
Skärmstorlek (skärm):	128 x 160 mm
Maximalt-djup:	73.2 m