KStrong UFL201131 Bruksanvisning
KStrong
ej kategoriserat
UFL201131
Läs gratis den bruksanvisning för KStrong UFL201131 (12 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 2 recensioner. Har du en fråga om KStrong UFL201131 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
USER INSTRUCTION MANUAL
ENERGY ABSORBING LANYARDS
THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODELS:
UFL201701, UFL201721, UFL201101, UFL201111, UFL201121, UFL201131, UFL204101,
UFL204111, UFL204121, UFL204131, UFL206101, UFL206111, UFL206121, UFL206131,
UFL201402, UFL201422, UFL201601, UFL201622, UFL201301, UFL201331, UFL204102 ,
UFL204112 UFL201421, UFL206214, UFL206234, UFL201621 AND UFZ800100
2
This manufacturer’s user instruction manual meets the requirements of ANSI Z359.18-2017. As per OSHA, this manual should be used as a part
of an employee training program.
WARNING
The products enumerated in this instruction manual are a part of a personal protective, work support or rescue system. It is important that the
user reads and follows the manufacturer’s instructions for each component of the system. This manual contains information which is important
to the user’s safety and should be kept in a safe place for future reference as needed. The instructions provided in this manual are meant for
the use of this equipment and should be read thoroughly and understood by the user before the equipment is used. Manufacturer’s instructions
must be properly followed for the correct use and maintenance of this equipment. Please contact KStrong for any questions regarding use of
this equipment.
Fall arrest systems and equipment are life saving products and are designed to reduce the potential of serious injury in the event of a fall. The
victim of a fall may also experience adverse effects due to prolonged suspension in a full body harness (FBH). However, it is important to note
that the user may experience an impact of force on their body in the event of a fall. In case there is a doubt about the user’s ability to utilize this
product, the user must consult a physician. Pregnant women and minors are not considered t for the use of this equipment.
TRAINING:
In order to ensure that the user is familiar with the instructions provided in this manual, it becomes the responsibility of the employer and user to
undergo training in proper inspection, use and maintenance of this equipment.
TECHNICAL SPECIFICATIONS :
Note: For Usage and instructions of lanyards UFL204102 and UFL204112 with Harness UFH10101P, Please refer KStrong Harness User
instruction manual.
S. No.
KStrong
Lanyard Model
Construction
of Webbing
Hardware
Minimum Breaking
Strength
Conformity
1. UFL201701 Aramid and Nylon Steel 5000 lbs. ANSI Z359.13-2013
2. UFL201721 Aramid and Nylon Steel 5000 lbs. ANSI Z359.13-2013
3. UFL201101 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
4. UFL201111 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
5. UFL201121 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
6. UFL201131 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
7. UFL204101 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
8. UFL204111 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
9. UFL204121 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
10. UFL204131 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
11. UFL206101 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
12. UFL206111 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
13. UFL206121 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
14. UFL206131 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
15. UFL201402 Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
16. UFL201422 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
17. UFL201601 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
18. UFL201622 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
19. UFL201301 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
20. UFL201331 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
21. UFL204102 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
22. UFL204112 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
23. UFL201421 Polyester and Nylon Steel 5000 lbs. ANSI Z359.13-2013
24. UFL206214
Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
25. UFL206234
Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
26. UFZ800100
Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
27. UFL201101(03)
Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
28. UFL201121(03)
Polyester and Nylon
Steel 5000 lbs. ANSI Z359.13-2013
3
The maximum arrest force of the personal energy absorber when dynamically tested in accordance with ANSI Z359.13 is 1800 lbs. The
maximum elongation of the personal energy absorber when dynamically tested in accordance with the same standard is 48 inches. When the
weight of the user is 220 lbs. (100 kg) with a free fall distance of 6 ft., the maximum allowable elongation is 37 inches (95 cm).
IMPORTANT INFORMATION:
• It is important to inspect the equipment according to the manufacturer’s instructions before each use.
• Inspection of equipment should be done on a regular basis by a qualied person and the results should be recorded in the inspection
log.
• DO NOT REMOVE product labels which include important warnings and information for the “Authorized Person”.
• “Authorized Person” is a person who is exposed to fall hazards during the course of their work. This individual requires formal
training in the use of personal fall protection equipment and systems. The term “Authorized Person” may be used interchangeably
with “User” and “End-User”.
• DO NOT ALTER the equipment in any way.
• Always send the equipment back to the manufacturer, or to the persons or entities authorized in writing by the manufacturer, for
any repairs if required.
• Never use any natural material like manila, cotton, etc. as part of the Fall Protection System.
• Fall protection equipment should only be used for the purpose for which it has been designed.
• This equipment should never be used for towing and hoisting or for any other purpose than its intended use.
• A competent person must ensure compatibility of the system to minimize any potential for accidental disengagement.
• Authorized persons or users shall be trained on all warnings and instructions provided in this manual.
• It is important for all authorized persons and users to refer to the applicable ANSI Standards and to the regulations governing
occupational safety.
• Take proper precautions to remove any debris, material, obstructions, etc., from the work area which could cause injury, or otherwise
interfere with the functioning of the system.
• KStrong Anchors should be used only with the combinations of components, sub-systems or both which may affect or interfere with
the safe function of one another. Be certain that connecting devices are compatible and that other elements of the PFAS are safe
and compatible before use.
• Always check for obstructions below the work area to make sure that the potential fall path is clear.
• Keep the equipment away from anything that could damage it such as sharp edges, rough or abrasive surfaces, high temperature
surfaces, heat and welding sources, moving machinery, electrical hazards, etc.
• It is important to keep in mind environmental hazards when selecting fall protection equipment.
• Do not expose the equipment to chemicals, highly corrosive or caustic environments, or to direct sunlight and UV radiation, which
may cause UV degradation.
• Such harmful environments require a more frequent inspection and servicing program of the fall protection equipment to maintain
the integrity and safety of the equipment. Contact KStrong if in doubt.
• All the synthetic material of fall protection equipment must be protected from slag, hot sparks, open ames or other heat sources.
• It is recommended that heat resistant materials are used in such applications. It is important to allow adequate fall clearance below
the work surface.
• Always have a Rescue Plan ready and at hand when using this equipment.
WARNING
• Immediately discard any product which is exhibiting unusual wear, deformity or deterioration.
• Immediately remove from service any equipment that has been subjected to a fall.
COMPONENT COMPATIBILITY:
Component compatibility with KStrong manufactured fall protection equipment is ensured by strictly following the instructions for each type of
equipment used. However, if the user utilizes combinations of components or sub systems that are manufactured by others, only a “qualied” or
“competent” person (as dened in OSHA) can ensure the compatibility. If substitutions or replacements are made with non-approved components
or sub systems, then this may severely affect the compatibility of the equipment, making the complete system unsafe for use.
COMPATIBILITY OF CONNECTORS:
To ensure the compatibility of the connectors with their connecting element, it is important to safeguard that the sizes and shapes of the
connectors and the connecting elements do not allow their gate mechanisms to open inadvertently, notwithstanding their orientation with each
other. All hooks, carabiners, D-rings and other such connectors must be capable of supporting a min. force of 5000 lbs. (23 kN). All connectors
must be compatible with all system components like anchorages, etc. Never use equipment which is not compatible as this may cause the
connectors to disengage unintentionally. All connectors must be compatible in shape and size. As per ANSI Z359.12 and OSHA, only self-locking
snap hooks and carabiners may be used.
Produktspecifikationer
| Varumärke: | KStrong |
| Kategori: | ej kategoriserat |
| Modell: | UFL201131 |
Behöver du hjälp?
Om du behöver hjälp med KStrong UFL201131 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat KStrong Manualer
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
ej kategoriserat Manualer
- Belkin
- Eastron
- Stairville
- Salter
- I.R.I.S.
- I-PRO
- Geuther
- Testboy
- LAFE
- Bose
- BenchK
- Texas
- Be Quiet!
- Bauhn
- Vorago
Nyaste ej kategoriserat Manualer
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025