KStrong UFL205401 Bruksanvisning
KStrong
ej kategoriserat
UFL205401
Läs gratis den bruksanvisning för KStrong UFL205401 (12 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 2 recensioner. Har du en fråga om KStrong UFL205401 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
UFL205201, UFL205211, UFL205251, UFL205202, UFL205215,
UFL205401, AND UFL205201(02), UFL205201(03)
THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODELS:
WORK POSITIONING LANYARDS
USER INSTRUCTION MANUAL
01
This manufacturer's user instruction manual meets the requirements of ANSI Z359.3-2017. As per OSHA, this manual
should be used as a part of an employee training program.
WARNING
The products enumerated in this instruction manual are a part of a Work Positioning System. It is important that the user
reads and follows the manufacturer's instructions for each component of the system. This manual contains information
which is important to your safety and should be kept in a safe place for future reference as needed. The instructions
provided in this manual are meant for the use of this equipment and should be read thoroughly and understood by the
user before the equipment is used. Manufacturer's instructions must be properly followed for the correct use and
maintenance of this equipment. Please contact KStrong for any questions regarding use of this equipment.
WARNING
This equipment is meant only for work positioning and should never be used for fall arrest. Fall arrest systems are
comprised of separate sub-components, which reduce the potential of serious injuries in the event of a fall. Work
positioning systems only aid in the positioning of the user at height, so that the user may work at height with both hands
free. The fall arrest system is separately connected to the wearer, and is necessary to be used along with a work
positioning system, so that complete safety of the user is ensured.
TRAINING
In order to ensure that the user is familiar with the instructions provided in this manual, it becomes the responsibility of
the user to undergo proper training on the proper inspection, use and maintenance of this equipment. It is also the
employer's responsibility to ensure that all the users are trained in proper use, inspection and maintenance of work
positioning and Fall Protection Equipment.
TECHNICAL SPECIFICATIONS
IMPORTANT INFORMATION
It is important to inspect the equipment according to the manufacturer's instructions before each use.
Inspection of equipment should be conducted on a regular basis by a qualified person, and results must be
recorded in the inspection log.
DO NOT REMOVE product labels which include important warnings and information for the authorized person.
"Authorized Person" is a person who is exposed to fall hazards during the course of their work. This individual
requires formal training in the use of personal fall protection equipment and systems. The term "Authorized
Person" may be used interchangeably with "User" and "End-User".
DO NOT ALTER the equipment in any way.
Always send the equipment back to the manufacturer, or to persons or entities authorized in writing by the
manufacturer, for any repairs if required.
Never use any natural material like manila, cotton, etc. as part of a Fall Protection System.
Fall protection equipment should only be used for the purpose for which it has been designed. Work positioning
lanyards are not to be used for material handling, and other such activities.
This equipment should never be used for towing and hoisting or for any other purpose than its intended use.
A competent person must ensure compatibility of the system to minimize any potential for accidental disengagement.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
UFL205401
Grade 80 (Straight Link)
Steel
1.
Min.10000 lbs.
ANSI Z 359.3-2017
KStrong Positioning
Device Model
Grade of Chain
Hardware
S.No.
Tenstile
Strength
Conformity
KStrong Work
Positioning Lanyard/
Device Model
Construction of
Webbing
Hardware
S.No.
Minimum Breaking
Strength
Conformity
UFL205201
UFL205211
UFL205251
Polyester & Nylon
Polyester & Nylon
Polyester & Nylon
Steel
Steel
Steel
1.
2.
3.
5000 lbs.
5000 lbs.
5000 lbs.
ANSI Z359.3-2017
ANSI Z359.3-2017
ANSI Z359.3-2017
UFL205202
UFL205215
UFL205201(02)
UFL205201(03)
Polyester & Nylon
Polyester & Nylon
Steel
Steel
4.
5.
5000 lbs.
5000 lbs.
ANSI Z359.3-2017
ANSI Z359.3-2017
6.
7.
Polyester & Nylon
Steel
5000 lbs.
ANSI Z359.3-2017
Polyester & Nylon
Steel
5000 lbs.
ANSI Z359.3-2017
ŸAuthorized persons, or users, shall be trained on all warnings and instructions provided in this manual.
ŸIt is important for all users to refer to the applicable ANSI Standards and to the regulations governing occupational
safety.
ŸTake proper precautions to remove any debris, material, obstructions, etc. from the work area which could cause
injury, or otherwise interfere with the functioning of the system.
ŸKeep the equipment away from anything that could damage it such as sharp edges, rough or abrasive surfaces,
high temperature surfaces, heat and welding sources, moving machinery, electrical hazards, etc.
ŸIt is important to select Fall Protection Equipment keeping environmental hazards in mind.
ŸDO NOT expose the equipment to chemicals, highly corrosive or caustic environments or to direct sunlight and
UV radiation, which may cause UV degradation.
Such harmful environments require a more frequent inspection and servicing program of the fall protection
equipment to maintain the integrity and safety of the equipment. Contact KStrong if in doubt.
ŸAll synthetic material of fall protection equipment must be protected from slag, hot sparks, open flames or other
heat sources.
It is recommended that heat resistance materials are used in such applications. It is important to allow adequate
fall clearance below the work surface.
Always have a Rescue Plan ready and at hand when using this equipment. The rescue plan should be provided to
an authorized person. The user should also be provided with appropriate training before using the equipment in a
situation where a suspension could occur.
WARNING !!
Immediately discard any product which is exhibiting unusual wear, deformity or deterioration.
Immediately remove from service any equipment that has been subjected to a fall.
COMPONENT COMPATIBILITY
Component compatibility with KStrong manufactured fall protection equipment is ensured by strictly following the
instructions for each type of equipment used. However, if the fall protection equipment utilizes combinations of
components or sub systems that are manufactured by others, then only a “qualified” or “competent” person (as defined
in OSHA) can ensure the compatibility. If substitutions or replacements are made with non-approved components of sub
systems, then this may severely affect the compatibility of the equipment, making the complete system unsafe for use.
COMPATIBILITY OF CONNECTORS
To ensure the compatibility of the connectors with their connecting element, it is important to safeguard that the sizes
and shapes of the connectors and the connecting elements do not allow their gate mechanisms to open inadvertently,
notwithstanding their orientation with each other. All hooks, carabiners, D-rings and other such connectors, must be
capable of supporting a min. force of 5000 lbs. (23 kN). All connectors must be compatible with all system components
like anchorages, etc. Never use equipment that is not compatible as this may cause the connectors to disengage
unintentionally. All connectors must be compatible in shape and size. As per ANSI Z359.12 and OSHA, only self-locking
snap hooks and carabiners may be used.
CONNECTIONS USING CONNECTORS
Ensure that only self-locking snap hooks and carabiners are used with this equipment. All connections should be
compatible in size, shape and strength. The connectors used should be suitable to each application. Ensure that they
are fully closed and locked while in use.
NEVER USE INAPPROPRIATE CONNECTIONS
While using KStrong snap hooks and carabiners, they should not be connected as below:
Two or more connectors should never be attached to a single D-ring.
Never attach a connector that could result in a load on its gate.
Connectors should not be connected in a false engagement. It should be visually confirmed that the connector is
fully engaged to the anchor point. Avoid conditions that allow for features that protrude from the connectors to
catch on the anchor, giving a false sense of being connected.
Connectors should not be connected to each other.
Connectors should not be connected directly to the webbing or to the rope lanyard or tie back, unless specifically
allowed by the manufacturer.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
02
Produktspecifikationer
| Varumärke: | KStrong |
| Kategori: | ej kategoriserat |
| Modell: | UFL205401 |
Behöver du hjälp?
Om du behöver hjälp med KStrong UFL205401 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat KStrong Manualer
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
24 Augusti 2025
24 Augusti 2025
24 Augusti 2025
ej kategoriserat Manualer
- Swann
- Profoto
- ESYLUX
- Mima
- Backyard Pro
- Neewer
- Dell
- Solplanet
- Cameo
- Hibriway
- Olympia
- Feit Electric
- Royal Catering
- McIntosh
- Lowrance
Nyaste ej kategoriserat Manualer
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025
25 Augusti 2025